Search results

  1. tg3690

    1994 Force 120 HP Ser. # 0E089004

    Looking at the diagram....the #1 wire coming out of the ignition switch is a black/yellow wire.....looks like it runs to a connector or something then turns into a single black wire that goes to the switch box....third position down from the top on the right side. It shows a ground wire for the...
  2. tg3690

    Think it's restorable....

    That Yammie might need a new impeller.....🤣
  3. tg3690

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    "Simplicity" is good....one of the downsides of adding a VR is they can fail without warning....leaving you adrift.
  4. tg3690

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    All a rectifier does is convert AC to DC current.....so there is nothing wrong with them.....you want to lower the high voltage.....so try the voltage regulator/rectifier and see if there's a difference. IF you have 16 volts at idle it is probably higher at higher rpms. On my engine it spiked...
  5. tg3690

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    Is your installed OEM "regulator" the Sierra unit you bought? If so, it is a rectifier only.....no voltage regulation....maybe try the CDI unit and see if it lowers the volts. I would not wire them both up.
  6. tg3690

    Struggling to install lower unit....Force 90Hp

    Take the spark plugs out and the flywheel will turn real easy....like racerone said get a helper to turn it while you muscle the LU on. Good idea to at least remove the plug wires when moving the flywheel anyway.
  7. tg3690

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    If you look up that part # on the CDI website there is an installation PDF....it says to use the existing mounting bolts, so I reckon it mounts in the same spot. Doesn't say anything about adding a heat sink.
  8. tg3690

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    If you can add water to it then it's not a real maintenance free battery. Should be good.
  9. tg3690

    1998 Johnson 90HP (J90TSLECM) voltage too high!!!

    https://forums.iboats.com/threads/if-you-have-high-charge-voltage-please-read.249235/ This thread has some info about your problem.....I did the conversion and it fixed my high voltage problem......also CDI says to only use regular lead acid batteries, no maintenance free, AGM, or dry cell...
  10. tg3690

    Doing some research on adding tilt trim

    The kingpin is what's holding the engine on....to remove it you would need a lifting eye mounted on top and a hoist.....major job. Do a search on here for "kingpin" and you will see what is involved.
  11. tg3690

    Wiring diagram?

    #9 is the thermoswitch for the overheat buzzer.....with the tan wire.
  12. tg3690

    Wiring diagram?

    This is for 120HP Force 1991B thru 1995....
  13. tg3690

    70s Chrysler 16hp outboard funny runner

    If unknown when the impeller was last changed you might want to do that first.....if it goes then anything else you do won't matter....found out the hard way a long time ago.
  14. tg3690

    E85 in Chrysler outboard?

    https://forums.iboats.com/threads/e15-and-no-rec-gas.755985/ This thread talks about how bad E15 is......E85 would probably kill an old Chrysler 2-stroke or any old outboard or small engine. If you are worried about the environment then get a 4-stroke engine.
  15. tg3690

    Force 85 trim

    Good deal.....those tilt/trim motors usually outlive the outboard motor it is mounted on. Might check/clean the electrical connections...in the switch and the battery. Might be time for a new battery too. A bad battery could cause the clicking you heard....not enough juice to turn it over...
  16. tg3690

    Force 85 trim

    That knurled knob where the green arrow is pointing is where you add oil. Engine must be in full down position when adding or checking. Use SAE 30 non detergent oil only. Add oil until it comes out....let the excess run out, then screw in the knurled knob securely, but not so tight as to...
  17. tg3690

    1972 Tillotson WB9B carburetor fuel bowl leak

    Have bought some parts from them also....nice folks.
  18. tg3690

    WATER PUMP LINER

    Another one bites the dust.....
  19. tg3690

    Cover over propeller drive shaft?

    One of these? It slides on the end of the prop shaft and covers the prop nut. Not used on Force engines I believe.
  20. tg3690

    Battery(s) for 1979 Chrysler 115 outboard

    Moderators....could you move this thread over to the Force/chrysler outboard section....for better views....
Top