Search results

  1. stresspoint

    First Start of the year and High Oil Pressure

    if i had to take a guess ????, i would be looking at the gauge or the wires going to it .
  2. stresspoint

    How to actually BOOK a flight online?

    it must be a common thing these days for price gouging on airline flights online. i went to the agency door after getting frustrated trying to get a flight , same thing as you , picked the flight , went to book and pay and the fare was no longer available or price jumped . the booking agent...
  3. stresspoint

    Suzuki DF150 stuck bearing carrier on lower unit

    how badly bent is the shaft , you may have to straiten it a bit with a steel tube , if its pulling on an angle IE: following a bend it will just lock up as its pulling. be sure your puller is strait in line and even distance all around.. if the rubber o ring is binding ,which it may well be now...
  4. stresspoint

    Thread repair on Bell Housing

    i don't think you will find a heicoil that thread , however it would be possible to drill it larger , tap a 12mm x 1.5 metric thread , centre drill a 12mm stainless bolt with a 1.5 thread and tap the required1/4x18 NPS to suit the cable. i don't know off hand the drill size required for that 1/4...
  5. stresspoint

    Can you use car oil in a Mercruiser 3.0 engine

    yes you can use that castrol 20w50, in fact i only use Valvoline regular mineral 20w50 oil in all my boat motors including my 500hp vortec 5.7, i use it in my 4.3 and it seems to have stable oil pressure through out the RPM range when i was running high output moded V6 4 stroke out boards i used...
  6. stresspoint

    First Start of the year and High Oil Pressure

    i would address this before moving on , that oil does not just disappear into space.
  7. stresspoint

    First Start of the year and High Oil Pressure

    let the motor warm up a bit IE: idle , and see if the pressure comes down before jumping to conclusions of something bad being wrong. it most likely will be fin once the oil thins a bit and circulates.
  8. stresspoint

    What are these tiny bubbles??

    osmosis is not the end of the world for a hull , usually its just in the gel coat. it can be sanded back and painted or some brush on waxed gel coat depending on where it is , in your case some brushed gel coat will do just fine or just be left alone..
  9. stresspoint

    Crusader 2004 Engine Ground Issue

    start by ripping all the harness out and testing continuity , before you question ripping /taking the wiring out , with it on the bench it is easier to bend and pull individual wires to test for breaks in continuity, you can also inspect plug connector pins ,you can also see places out of sight...
  10. stresspoint

    4.3L OMC Cobra 1988 engine knock/rattle

    i recon it may be an exhaust flapper. just a guess and an easy examination.
  11. stresspoint

    New intake...port for pcv and for vaccume

    i prefer to use a port from the carb for vac gauge , i don't know why iv just done it that way for years. PCV i also like to tap into the rear of the carb on Holley rather than the manifold , i have done the same on my quadrajet that's on my 4.3 , some say PCV is not needed on marine engine but...
  12. stresspoint

    Mercruiser 4.3 Temp Alarm Question

    is the drive oil reservoir full ?. try taking the reservoir off and flushing it , the float sensor may be sticking. reason i mention is mine random beeped and a sticking float was the issue.
  13. stresspoint

    Replacing 95 merc 4.3 with 87 OMC 4.3

    the early ( non balance shaft ) Mercruiser flywheel will bolt up to early motor , the problem you could run into as i did is the ring gear teeth being a different pitch , as from what i found there are 2 types of early non balance shaft FWs one is for a geared starter (vortec type) and the...
  14. stresspoint

    Replacing 95 merc 4.3 with 87 OMC 4.3

    yes it was a learning curve let me tell you , point being , don't expect a bolt an go with that early OMC motor , it will work "but :)"you will have to strip to a long block and go from there ,end of the day IMO it will be no where near as good the later model balance shaft version. as you...
  15. stresspoint

    Replacing 95 merc 4.3 with 87 OMC 4.3

    one motor is later vortec the other is early vortec often said to be non vortec. ? confused :) so was i when i bought a replacement early motor thinking it was a swap and go affair. https://www.thehulltruth.com/boating-forum/1211569-giving-some-much-deserved-love-restoration-thread.html start at...
  16. stresspoint

    OMC 460 backfire under load

    buy some new ignition parts , points, cap , rotor , coil and condenser ( i know you posted these have been replaced but start again anyway). if you have a ballast resistor replace that to. I'm guessing the points are cooked "but " a condenser or coil will give similar symptoms.
  17. stresspoint

    RE: Issues with Mercruiser 5.0 LX 4 Barrel Carb

    i still sometimes set the lash with the motor running > back each nut off till it clacks then wind it down 1/2 a turn. love the smell of burning oil on a hot extractor :) .
  18. stresspoint

    Evinrude 25 Lean sneeze

    when i get a 2 smoke that has a sneeze i spray some carb cleaner around the intake area , well basically i drown the motor in the **** :) . one place to also spray carb cleaner is into the air fuel mixture screw on the smaller 2 cylinder motors if it idles up there is your issue ,
  19. stresspoint

    MerCruiser 5.0 MPI pinging/detonation at higher RPMs

    something going on there with that dizzy that don't look right , can you try to post a pic or vid of where the moving originates from. you may need to remove the dizzy to inspect this will mean it needs to be clocked again , that is no problem because you will know everything is correct.
  20. stresspoint

    Show me a better or more unique sounding short block v8 than this wee monster !

    my Mercruiser 5.7 sounds better :) .it is however 500hp , i get plenty of comments on how good it sounds @6800 rpm. occasional whine from someone about it being annoying , but hey :) you cant please everyone . i just tried to upload a vid but apparently file is too big ,so just a pic for now.
View older results
Top