Search results

  1. flyingscott

    Amazing

    Your motor is a1.7 litre I4 how is that double
  2. flyingscott

    Disconnecting Fuel line from the outboard

    I would be curious to know if you could even put enough pressure in the line to make the injectors work properly?
  3. flyingscott

    Transom Browning

    They did not clean the boat off. That happens when boats are kept in the water. Look on craigslist dozens of boats have that stain.
  4. flyingscott

    Serial number not showing up

    Where ar you from?
  5. flyingscott

    Crack in Hull

    Really the boat was well maintained yet it has a crack in the hull? Really That is an old crack. Not to mention it looks like they hit something to cause that.
  6. flyingscott

    1957 evinrude fastwin 18hp ventilation problems.

    That motor has points and condensors under the flywheel.. You should move this to the johnson evinrude Forum. Spark plugs are not your problem.
  7. flyingscott

    1957 evinrude fastwin 18hp ventilation problems.

    It sounds like your motor is running on one cylinder do a spark test. That motor I believe is only rated to 4500 rpm.
  8. flyingscott

    Crack in Hull

    I will be blunt Screw the complete overhaul. Go buy a different boat and chalk this one up as a learning experience.
  9. flyingscott

    Wheel bearings full of water

    Personally I do not think bearing buddies are worth the money. They really only lube the closest bearing and do nothing for the other one. So not worth the time or money. Make sure you are getting the right seals. Are you packing the bearings? Are you filling the cavity between them? Best way to...
  10. flyingscott

    Transom Browning

    looks like a water stain.
  11. flyingscott

    Crack in Hull

    I will bet that costs more to fix than the boat itself is worth even if you do it. You are only seeing the crack gaurantee it is 100x worse once you get in there. Pull the drive and engine sell them scrap the hull buy a different boat.
  12. flyingscott

    Need prop for low speed manoeuvres

    This is a case where you need to learn how to drive your boat at low speeds. A little bit of practise goes a long way there is no magic prop for that.
  13. flyingscott

    97 20HP Merc Inlet Needle

    Get a good rebuild kit for that carb. Should include fuel pump and primer assemblies.
  14. flyingscott

    1993 70hp stumped!

    That makes sense you have an 1986 block because those compression #s would be high for a 93 block. Somebody replaced the block at one time or another no big deal. The carbs and ignition will work fine on it. Those motors were not the smoothest idling motors so dont expect a lot..
  15. flyingscott

    1990 Evinrude 9.9HP Powerpack

    Well if you say so.
  16. flyingscott

    1993 70hp stumped!

    What is the model # of the motor?
  17. flyingscott

    2005 140 hp VRO failure & fix

    You can buy rebuild kits for them. Make sure you follow the procedure for bleeding the new pump. And is a good time to change the filter in the oil tank and clean it.
  18. flyingscott

    125hp ELPTO 2+2 miss/hesitation at high speeds

    Check the stator.
  19. flyingscott

    1990 Evinrude 9.9HP Powerpack

    Didnt realize I had to point out the cdi sits on top of the block under the flywheel in the heat. I thought that would be obvious. If it was a good ignition it would have been around for more than 4 yrs.
  20. flyingscott

    1990 Evinrude 9.9HP Powerpack

    Buy the conversion kit that gets the cdi out from under the flywheel. That was not a great set up had a high failure rate.
Top