Search results

  1. flashback

    port side exhaust elbow over heating.

    A couple of pics of the other end of the riser. It doesn't look good to me. Every thing else is probably about the same, I'm thinking it's time for a new exhaust complete.
  2. flashback

    Want to make my 350’s louder

    I like a nice rumble but I wouldn't call it loud.
  3. flashback

    port side exhaust elbow over heating.

    A bit of background, I got the boat last summer and after replacing the rubber bits and gimbal bearing, shift cable I ran it through the break in procedure for a new SEI drive because the PO had it installed but never broke it in or used it. The way the bearing was screaming I'm happy he didn't...
  4. flashback

    port side exhaust elbow over heating.

    Thanks for digging into this with me.. Yes the down elbow was already getting warm the riser and manifold still cool, it seems like the water isn't getting into the down elbow or maybe the flapper being stuck was holding the water from getting out.. something bent the flapper rod unless it's...
  5. flashback

    port side exhaust elbow over heating.

    Can you still get metal flappers, I can straighten it out if needed. How can I test the riser for flow, I thought maybe just Hook it to a hose and see where the water comes out..
  6. flashback

    port side exhaust elbow over heating.

    No, I didn't run it long enough to get hot cause at that point I wanted to get it apart without burning my lilly white fingers. What should I look for on the riser? I picked a bit of rust out of it.
  7. flashback

    port side exhaust elbow over heating.

    Finally had decent weather and was able to work on the boat today. I pulled the hoses from the riser and manifold and water flow seems good. So I put them back on and cranked it up to see if the elbow would heat up. I saw water coming out of the lower exhaust boot at the y pipe so pulled the...
  8. flashback

    Weight distribution on trailer bunks and rollers?

    I may be mistaken but I believe that the bunks support the boat and the roller is just a guide to keep the boat centered..
  9. flashback

    Bilge Vent Puzzle?

    Makes sense to me, the passive holes are probably for heat dissipation.
  10. flashback

    Merc won’t engage motor into drive

    What Bondo said, Been there and done it ! Real easy get mis-aligned...
  11. flashback

    Movement right to left in alpha outdrive

    There are several linkages that compounded can create a good bit of slop in an older boat. Be sure the clinch bolts on the gimbal ring are to spec. That's where you can run into some big problems if not tight..
  12. flashback

    Think it's restorable....

    This is starting to look like a re-birth of Silver Springs ...
  13. flashback

    Cracked 5.7 engine

    It's all relative, kinda depends on how old you are and how long it needs to run..
  14. flashback

    Air Don't Freeze Winterization

    I guess it depends on environment , l live in a cabin on a steep slope where they're is no flat land. It's much better for me to trailer the boat a half mile, ease it into the lake, fire it up and then go from there. I'm not sure if my well could offer enough volume 300 feet up from the cabin...
  15. flashback

    Cracked 5.7 engine

    You might be able to get a short block and use the parts from your engine to finish it off. But be damn sure the parts are good..
  16. flashback

    Cracked 5.7 engine

    There's 2 significant cracks I see but there are more that these old eyes can't see. Ice damage is brutal to cast iron..
  17. flashback

    Cracked 5.7 engine

    I patched up a manifold with JB weld and it's still going 15 years later, but it has no moving parts creating power. You need a new engine.
  18. flashback

    Preparation before applying 5200

    Why do you want to put sealant around the drives? I may get flogged for this but if you're trying to stop a leak you may have bigger troubles.
  19. flashback

    Air Don't Freeze Winterization

    In the puddle I play in there's not enough O2 in the lake water to cause rust but it still freezes! They have to pump it in to keep fish alive..
  20. flashback

    Fuel Tank Shape - Lesson Learned

    The way I see it you need to make the pads conform to the hull or the hull conform to the pads. If you have a Way of slicing some new pads diagonally then glue them on top of the existing ones.
Top