Search results

  1. Faztbullet

    under powered mercury 125 / 2 stroke

    27 knots is somewhat fast ..what is your RPM at WOT?
  2. Faztbullet

    Prop advice needed

    Working at the nations largest HydraSport and Checkmate dealer in the 80's, we sold several hundred of these and never had a gearcase fail. Being the shop foreman and lead tech I set all of the Checkmates up for max performance. Only problem we had from these props(TS and Merc's Version) was...
  3. Faztbullet

    Prop advice needed

    Look over on Ebay and find ya a torque shift prop..it will blast ya out of the hole and depending on cam you can set top end pitch.
  4. Faztbullet

    Idle mixture screws adjustments 135 hp 1990 Mercury

    IMO not necessary. If it doesn't spray it has a problem
  5. Faztbullet

    Anyone know of a Quality Aftermarket Yamaha parts supplier

    SEI or WSM or ProMarine
  6. Faztbullet

    Prop advice needed

    Naaa...just had to go to the right place to get em. No thru hubs raced in the Mod VP or F1 Tunnel series.
  7. Faztbullet

    Boat Randomly Sluggish

    Could be a coupler on its way out....
  8. Faztbullet

    Hole shot to plain very very slow

    Motor if mounted on hull should be in the 3rd hole...vented 24 pitch prop if Raker or 25 if a Turbo(best) and if its lazy out of hole and doggy on top end ..tighten the high speed jets as they do come loose and cause these issues.
  9. Faztbullet

    Prop advice needed

    Thats a Mercruiser/Outboard thru hub cleaver..below is a racing cleaver for tunnels . They are usually 10.5 to 11" in diameter and run with 1 blade in water. The B1 drive has a lot of drag and best to use biggest diameter prop you can get.
  10. Faztbullet

    Idle mixture screws adjustments 135 hp 1990 Mercury

    Fire it off and while running pull the hose off nipple with long reach needle nose. It should spray out in a fine mist, if thick or sputters they need clean/replaced
  11. Faztbullet

    Evinrude V4 120GT Looper Mixture Screw Settings

    Will it idle?
  12. Faztbullet

    VST Mercury 60 4 stroke EFI

    Floats stuck or debris under needle not letting it seat...basically it is flooding
  13. Faztbullet

    mercury 500 50HP water exhaust cover issue

    If it came from factory blocked ...leave it blocked.
  14. Faztbullet

    Replace 2002 115hp lower unit

    All the metric lower units will interchange. Only difference is ratio and clutches. You can put a 1987 unit on a 2007 if you have the correct linkages to make shift throw length correct and shift shaft. Around 1997 Merc went from a 3 jaw to 6 jaw clutch and the throw length is different. Also in...
  15. Faztbullet

    95 Merc 60 HP trigger ohm out of spec

    More testing...get a DVA meter and check outputs. Could be switchbox rectifier as around 2krpm is when it swaps from low to high
  16. Faztbullet

    20 seconds to start peeing on muffs

    Normal....
  17. Faztbullet

    Can I use a Johnson/Evinrude tank on Merc outboard?

    If its a newer plastic EPA tank it will need a vent fuel cap to work. If its a old metal one it will work fine
  18. Faztbullet

    Tilt and trim

    What is the part number stamped into side of cylinder?
  19. Faztbullet

    Idle mixture screws adjustments 135 hp 1990 Mercury

    It gonna smoke with premix and if recirc valves are clogged even a lil more till the reeds clear out. Clean the ricirc valves and check fuel pump diaphram just for giggles
  20. Faztbullet

    Will evinrude work on johnson

    No ..you will need to get the 2 piece one.. Use the puller to remove the one from the 1996 unit and take the new driveshaft and pop it in place, reinstall impeller components and install you old shift rod to spec height..
View older results
Top