Search results

  1. 9

    Lower gearcase on 2005 f150

    pressure test it to find where and how bad it leaks. hard to believe all the lube leaked out and it was not also full of water
  2. 9

    2001 OX66 stumbles at idle after running wot

    Oh, so the line large was suppose to be linkage. the pressure regulator can be tested to make sure it does its thing correctly
  3. 9

    2001 OX66 stumbles at idle after running wot

    not sure what the changing of the oil pump has to do with your problem or what the line large hanging up is about. Or how changing the oil pump would affect the fuel pressure regulator screen. monitor the fuel pressure to see what it is doing when the problem shows up. moving the throttle...
  4. 9

    2001 OX66 stumbles at idle after running wot

    How many different OX66 did Yamaha produce in 2001? every one of them should have a model # on the bracket.
  5. 9

    2001 OX66 stumbles at idle after running wot

    strange, 3 years and still no one has a clue what motor you have
  6. 9

    Looking for pump to drain oil through dipstick tube

    fire the motor up and get it warmed up , shut off, and pump it out. long as you get the tube to the bottom of the pan it will be the same as pulling the drain plug. what do you think will be so heavy that it would settle out into the bottom of the pan and not be able to suck it out?
  7. 9

    Looking for pump to drain oil through dipstick tube

    what does what you fear have to do with his question?
  8. 9

    Suzuki DT 140 2 stroke carburetor version tilt and trim stuck in down position

    sorry, but I do not know much about a Suzuki motor. I have no idea what Suzuki does to limit tilt or even if it does
  9. 9

    2000 200hp Saltwater series 2 stroke SX200 spark plug

    normally there is a sticker on the motor somewhere indicaing what plugs should be in it. but a owners or service manual should give the proper information
  10. 9

    Suzuki Dt16 Starter

    is the side pressure you put on it acting as resistance to keep it from turning too easily which in turn causes it to rise instead of just freely turning around maybe
  11. 9

    Suzuki DT 140 2 stroke carburetor version tilt and trim stuck in down position

    if moving the motor around affects this, you have a bad connection or wire itself
  12. 9

    2001 DF70 won't go over 3000rpm

    thanks for the update , I do not think anyone could have guessed that was the problem I am sure you will double check things to make sure from now on. and others looking to solve similar problems will need to double check things they did also if they read this post
  13. 9

    Suzuki DT 140 2 stroke carburetor version tilt and trim stuck in down position

    if you have 12V+ heading to the T&T relay when you operate the switches either the relay is bad or you have a bad connection on the Pos or neg somewhere to the relay. have you tried jumping the relay to see if the relay or motor will operate?
  14. 9

    Suzuki Dt16 Starter

    if it fell out how would it work just sometimes?
  15. 9

    Boat going in reverse but not forward.

    since the OP did not give the motors model number we have no ideaa what it is. but Yamaha switched to a twist to shift in 1995 ,I would have to guess his 80s 40 is a push and pull shift rod. drop the lower unit again and place the lower unit in reverse and the shifter in reverse and hook back...
  16. 9

    1996 15 HP mercury with spark on only one plug

    what are you calling the ignition you want a pic of and what does it have to do with the operation of the trigger? I did finally find this on the CDI electronics trouble shooting web site for mercury's, but not for the 1996 15 hp section. The center hub on the flywheel also contains magnets...
  17. 9

    1996 15 HP mercury with spark on only one plug

    I do not have a pic of the flywheel, but if you read my posts above you will see it is the center ring of the flywheel that the trigger rides next to. the outer ring of the flywheel has 2 magnets and the stator LS and HS charge coils and the lighting coils are what those magnets run by
  18. 9

    1996 15 HP mercury with spark on only one plug

    why would it be sparking on one plug and not the other. there are no magnets passing by the trigger that I can see or detect. I would think it would need 2 magnets 180 deg apart positioned in opposite N S poles to give it the Positive and neg pulses. my question has been and still is , how...
  19. 9

    1996 15 HP mercury with spark on only one plug

    He said he checked the numbers on the original switch box, to order the ones he did troubleshooting info says it should have Pos and Neg pulses out of the trigger that fire different SCRs in the CDI. I am not seeing any neg pulses going to the CDI. swapping the trigger leads into the CDI...
  20. 9

    1996 15 HP mercury with spark on only one plug

    I am down to either the flywheel that gives the trigger the magnetic pulses is bad or the new trigger is bad. this is why I asked how this trigger is supposed to do what it does. and no one can explain how it functions/works, so it is a head scratcher.
Top