Search results

  1. 9

    Fresh water corrosion and anode choices…

    you seem to have missed the part about stray current mentiond. that can eat up metal quickly.
  2. 9

    2002 Suzuki df70 overheating

    yes pieces of the impellor can plug up passages, causing over heat. you can try dropping the lower unit and pulling the stat out and hooking a water hose directly to the pipe up to the power head and injecting compressed air into that also as you try flushing things out. but you may have to...
  3. 9

    Yamaha sluggish acceleration

    wild guess is eithr the fuel pump leaking fuel into crankcase or pilot jet/passages . take the carbs apart and pump to see if there is a problem you can see
  4. 9

    Diagnosing what looks like a dead stator

    someone, either you or someone else needs to measure peak voltages into the CDI and out of it to figure out what is bad
  5. 9

    Identifying a 75hp 2stroke (i think) 2005 with missing model number (and it won't start )

    I would think Boscoe99 could pin that down for you
  6. 9

    Yamaha 90 2 Stroke No Spark

    re reading yu posts, all I can think of is you have a bad connection somewhere or a short to ground on the kill wire, kill switch or key switch. there are no 2010 2 strokes here ,so not much we can look at seems you moved something around that caused the spark to show back up. I would be...
  7. 9

    Yamaha 90 2 Stroke No Spark

    I have a feeling they would tell you to use the proper test equipment to take readings or take the motor to someone that could
  8. 9

    Lower unit leak

    can you explain what a peepop valve is
  9. 9

    Lower unit leak

    the drain a vent screws have gaskets that should be replaced. and then retighten the screws after running the motor on the water just to be sure they are still tight. the gaskets crush down and will leak some times after putting new ones on.
  10. 9

    Lower unit leak

    remove the drain screw from the lower unit to check for water , get a little on your finger, and smell the lube while you are doing that. then smell the oil for the power head.
  11. 9

    Lower unit leak

    did you smell it to see if it was lower unit lube or oil from the power head?
  12. 9

    Yamaha 90 2 Stroke No Spark

    might try looking here https://www.cdielectronics.com/support/ if not the switches then maybe the wiring has a intermittent grounding of the wire that kills the spark I have never tried taking AC voltage readings ,so I have no idea how that would compare to specs
  13. 9

    Yamaha 90 2 Stroke No Spark

    need a peak voltage reading meter made to test these CDI systems or a DVA adapter and regular meter set on DCv look up CDI electronics trouble shooting guide on line to see if reading that helps you understand some of the stuff in your manual the key switch turned to off and/or the man...
  14. 9

    2008 90TRL need more power!

    yeah, I would like to be able to find all those old 2 stroke performance Bulletins myself. I have no idea what they did with all of those we use to be able to look at.
  15. 9

    2008 90TRL need more power!

    did it hit the speeds listed on the performance Bulletin? I just looked and that one you posted showed a F90TLR. And it would run 41.2 MPH at 5900 RPM. is that what the 13 pitch does?
  16. 9

    2008 90TRL need more power!

    very strange that you had to drop down to a 13 pitch if the performance bulletin showed an 18. you need to find out if the motor has a problem or if boat does. See if any of the shops around you have a test prop for that motor. they should be able to test it in a tank to see if the motor will...
  17. 9

    Yamaha 2-stroke 50HP 1980's bogs and not reaching max RPM

    it is the hole on the backside of the pump into #3 crankcase that furnishes the pulse to the pump diaphragm
  18. 9

    Yamaha 2-stroke 50HP 1980's bogs and not reaching max RPM

    usually just remove the pump from the block and pump the bulb to see if any fuel come out the pulse port not along the edges. with the bolts removed you might see leaks between the parts
  19. 9

    In-water testing for overheat. How hot is too hot on your hand?

    so you are saying the water pump is 20years old? replace it before it falls apart and sends pieces into the block that causes problems and you will need to go find. replace the parts broken, missing, or just need replacing due to age. use an infrared gun to get temps, everyone has different...
  20. 9

    OX 66 - oil vent hose hanging , Where does it go

    complete motor ID helps other know what you are talking about. but I guess you have no idea what you have so it is what it is. I am sure Yamaha did not cap off the drain, but I could be wrong I guess
Top