Search results

  1. R

    Older Boats

    Some older boats might be simpler to rebuild then some of the new stuff.
  2. R

    Did I get a bad regulator?

    My book says 0 .55 ohm +/- .05 ohm
  3. R

    Did I get a bad regulator?

    I think you have a bad stator.
  4. R

    Did I get a bad regulator?

    Did you take any readings on the stator ?
  5. R

    1990 50 hp Johnson reed valves

    When you push the key in ( motor running ) the electric primer VALVE opens.-----Fuel is then injected onto the intake air stream.-----This fuel bypasses the metering circuits in the carburetors.-----To me this indicates an issue with the carburetors.----Checked flywheel key ?-----Water pump...
  6. R

    1990 50 hp Johnson reed valves

    If it starts and runs for a few seconds it is not a reed problem.----------What happens when you operate the manual fuel pump ?-----What happens if you push the key in when it falters ?-----How did this motor run for you last season ?
  7. R

    Buy a 5hp Mariner with a blown head gasket?

    I would make a dummy exhaust cover to use as a drill guide.------Drilling a steel bolt in an aluminum housing can be tricky without a drill guide.
  8. R

    Buy a 5hp Mariner with a blown head gasket?

    ??----Find the parts at a Mercury dealer.-----Find the parts at a Yamaha dealer.---Boats.net ---online has good prices.-------Your choice.
  9. R

    2 Cylinder Johnson 40hp Old Trim/Tilt

    Read before you bring out the hammers.-----Both cylinders trim at the bottom.-----Only 1 cylinder tilts I believe.-----The 2 cylinders are NOT identical.
  10. R

    88 spl stiff shift rod

    Use a 5/16" drill bit by hand .------Scrapes any corrosion out in seconds.
  11. R

    Outboard motor upgrade?

    Aluminum is bad for fatigue cracking.-----Have heard of motors falling off pontoons after welds cracked.
  12. R

    Outboard motor upgrade?

    I think you would want to strengthen the transom.----At one time a 125 HP 2 stroke was about 252 LBS.----A modern 150 HP 4 stroke might be 531 lbs.
  13. R

    Buy a 5hp Mariner with a blown head gasket?

    That appears to be a Yamaha built motor.-----Some will say that they are the best !
  14. R

    88 spl stiff shift rod

    Any corrosion on the bushing can be cleaned.----The o-ring in there can be replaced.-----Simple fix here.-----And this is only if corrosion is the issue.----And only if the shift rod is tight in the cover !!!-----And at $2.00 / minute some dealers are happy to install a new cover to add to your...
  15. R

    88 spl stiff shift rod

    I do know how these motors / gearcases are put together !
  16. R

    Commonality with Auto Works

    Controls and location should be made somewhat standard.----Talk about distracted driving while finding wiper control.----Or how to set defroster in motion.-----Never mind the controls in electric vehicles.----Not easy for seniors !!
  17. R

    88 spl stiff shift rod

    Good luck with it.
  18. R

    Does anyone remember when car & boat engines only had.

    Have a set ( NOS ) of those points right here.
  19. R

    88 spl stiff shift rod

    ????------The shift rod screws into the mechanism way down in the gearcase.----So if you disconnect it you find out if the issue is the jammed bushing or not.----Part of the bushing is outside and away from any oil !-----Not sure who these people are with the marvel oil !!-----Shift rod needs to...
  20. R

    Does anyone remember when car & boat engines only had.

    Starter switch might foot operated , right above the gas pedal.----My 1940 Plymouth was like that.----Dimmer was also foot operated on many cars.
Top