Search results

  1. R

    Gearcase interchangeability

    The crankshaft spline is different.----Exhaust housing gasket is different.------So in short , there is no way that your idea will work.
  2. R

    1996 Evinrude Vindicator 200hp--engine keeps quitting on start-up

    This site does not like it----But lots of used primers in my area too.
  3. R

    1994 Mercury 60hp Poppit Spring

    The pump is driven by the driveshaft.-----And it will turn at engine RPM.-----Propshaft RPM will be lower with some bottom ends.
  4. R

    Wellcraft 190 ccf engine install

    Why are we discussing this again?----Was this not resolved weeks ago ?
  5. R

    1996 Evinrude Vindicator 200hp--engine keeps quitting on start-up

    The primer valve is fed by the fuel pump when the engine is cranking.----Or when the bulb on the hose is squeezed.------And fuel from the primer valve does NOT bypass the fuel pump.---It bypasses the carburetor bowls and metering circuits !----Lots of used factory ( and good ) primer valves are...
  6. R

    No water coming out the Merc tell tale now?

    There must be a leak.-----Leaking float valves?--Ruptured fuel pump diaphragm?----Bad primer bulb ?---Air leak between bulb and fuel tank , including inside the tank.----All simple for you to check.
  7. R

    No water coming out the Merc tell tale now?

    When you buy a used motor you must install a new impeller.-----And possibly the pee hose is plugged.----Test the overheat warning horn too.
  8. R

    1996 Evinrude Vindicator 200hp--engine keeps quitting on start-up

    These primer valves are very simple.-----Very reliable.-----Used from 1980 to 2005 on motors from 9.9 to 300 HP.-----Lots of good used ones are around.----See post #5.----Yes the mechanic was correct in his explanation.
  9. R

    Evinrude 1994 150

    Overheat is a steady alarm.----Low oil alarm should be disconnected if you are mixing 50:1 in the tank. .----Sounds to me there is a fuel restriction / blockage on hoses or inside fuel tank.----Check tank vent as well.----If you just got this motor you did install a new impeller ?
  10. R

    Unsure of year model

    I know that tell tale exits the lower cowling.----Reading post #7 carefully can only be for your benefit.
  11. R

    Salvage auction boat - can this be repaired?

    What $$$ are you expecting to have to invest in this to bring it home before repairs are done.----Perhaps hire a surveyor to give you an opinion.-----Any other pictures of this boat.----Is the damaged area accessible from inside?----Is this boat still in production for factory support?----Is a...
  12. R

    Salvage auction boat - can this be repaired?

    ??---SIR ?
  13. R

    Shift rod adjustment

    ???----I said to screw the coupler on and back it off as needed.----Seems clear and simple.----I own more than one of those gearcases.----No need for a manual here to work on one either !
  14. R

    Shift rod adjustment

    The coupler on top of shift rod screws down all the way.-----Then back it off as needed to position it.----Simple.
  15. R

    Shift rod adjustment

    Did an issue show up suddenly ?----What is your motor doing / not doing?-----Was the lower unit off for water pump work ?-----Is the lower unit full of HI-VIS oil ?
  16. R

    Unsure of year model

    In North America they used a trim switch on the lower cowling beginning in 89 I believe.----Not sure of the marketing strategy where you are.---And of course many sellers / dealers have put newer decals / hoods on motors.------Pictures of the powerhead ( 4 ) may or may not help with identification.
  17. R

    Unsure of year model

    My wildest guess is 1992 / 93 for those decals.----Post picture of other side of lower cowling.-----And does hose for tell tale come off the side of the block ?----Or was it moved per service bulletin?
  18. R

    Salvage auction boat - can this be repaired?

    Is that an aluminum hull ?----Did boat sink ?----If yes , were the motors looked at after recovery ?----Looks like a proper structural / cosmetic repair might be $10,000 / $15000 At many places I think.-----If you can find a shop with a low overhead that has cheap labor it might be very doable.
  19. R

    1990 40hp Evinrude control box no power

    Sounds like the fuse blew again.----Some testing required to determine why the fuse is blowing.-----I refrain from trying to explain electrical stuff.----It can be frustrating to explain fuses and such to a novice from 1000 miles away.
  20. R

    1990 40hp Evinrude control box no power

    Check the fuse on the motor.----Near the solenoid.----A 20 amp about 5/8" long inside a rubber boot.----The lower units on these motors are not robust enough to carry the loads.----Use the best ( dealer ) gear oil in there.----Install a new water pump impeller as well.----Test the overheat...
Top