Search results

  1. tpenfield

    Electro-Mechanical Trim Indicators

    the next step was up at the helm where the interface modules connect to the existing trim gauges. Here is the gauge panel removed and the wiring exposed The modules are plug 'n play with the gauge connectors, as it has 'piggy back' connectors, so no wiring work is needed at the helm either...
  2. tpenfield

    Electro-Mechanical Trim Indicators

    Update: I did the installation of my electro-mechanical indicators this weekend. Overall things went pretty good. I do need to mak a few tweaks to the electronics, but the system seems to be OK for now. First thing was to drill 2 5/8" holes at a pretty shallow angle in the underside of the...
  3. tpenfield

    Formula 330 SS Head Liner Refubishment

    Thanks guys, for the good words on my handy work, here are a couple more pictures . . . I used one of the poles from my mooring cover, along with some other stuff in the cabin to hold the forward section up while I secured it to the ceiling. The headliner is screwed into the ceiling at the 3...
  4. tpenfield

    Formula 330 SS Head Liner Refubishment

    Here is the rear section installed. Things were getting difficult at this point. Another view of the rear section Here is the forward section installed, along with the lights, etc. The seam looked OK, and the 2 screws that attach the 2 sections seems fine too. At some point, I'll probably...
  5. tpenfield

    Formula 330 SS Head Liner Refubishment

    Update: I finished off the headliner today. I was quite a bit of work installing it into the boat . . . overall I would put this project at an 8 on a 10 scale. Here are some pictures of the day. Cutting out the material for the headliner sections I used spray adhesive on the headliner board...
  6. tpenfield

    Question about filling Bravo III outdrive w/ Gear Lube . . .

    Yea, so I filled my twin Bravo 3 outdrives with gear lube yesterday, and that was a lot of 'fun' :rolleyes: In doing so, it has prompted some questions. I recall reading through the service manual a couple years ago and if I remember correctly, 1) I take the upper plug out, 2) fill from the...
  7. tpenfield

    Formula 330 SS Head Liner Refubishment

    The material arrived today . . . sort of wish it came a day earlier as I would have been able to knock this off over the weekend. Looks the same . . . maybe a bit darker than the original.
  8. tpenfield

    Electro-Mechanical Trim Indicators

    Update: I was planning on doing a test fitting and install the trim indicators this weekend . . . but . . . it looks like there is a wiring harness routed to where I was planning on mounting the potentiometer portion of the system. So, I am doing a bit of re-thinking and will probably take a...
  9. tpenfield

    Formula 330 SS Head Liner Refubishment

    Some Updates . . . My headliner material should arrive early this coming week. This weekend, I did some prep work on the headliner, and will probably do the installation next week. Here are a few pictures . . . I terminated the wiring that I had to cut for the lights. So, going back in, they...
  10. tpenfield

    Subscription Notifications not going away after delete

    I am noticing that the subscription notifications in the message center are not going away when I click to delete them. They used to, no problem. This just happened with the recent site maintenance.
  11. tpenfield

    New Anchor and Bow Roller

    Here are some pics of the wiring . . . I ran some 4 GA wire from the engine room, up the port side and then through the ceiling of the cabin to tie into the existing wiring harness. I also ran a 12 GA Trilpex wire to the helm for the windlass switch. Feeding the 4 GA wire down the port side...
  12. tpenfield

    New Anchor and Bow Roller

    A fairly big weekend on the boat project front . . . I have been meaning to put a new anchor and a windlass on my boat. This year, the budget got stretched a bit on some other issues, so I decided just to do the new anchor and roller this year, and then the windlass next year. I decided to go...
  13. tpenfield

    Formula 330 SS Head Liner Refubishment

    Thanks. :) After a bit of inspection and some dis-assembly, it looks like I will need to get new headliner material. I was hoping that the foam backing would be in decent shape and re-usable, but that is not the case. I also have noticed that the headliner is made up of 2 pieces of 1/4"...
  14. tpenfield

    Formula 330 SS Head Liner Refubishment

    Here is the headliner (center section) in my living room for the evening. I plan to refurbish it outside tomorrow, as the weather will be dry. I took the opportunity to check out the wiring runs, as I plan to add wiring for a windlass (to be installed next year - maybe) The outside sections...
  15. tpenfield

    Formula 330 SS Head Liner Refubishment

    I noticed that the headliner cloth was hanging down at the end of last season. The cloth seems to be separating from the foam backing, etc. So, I planned to do a little bit of work on it as part of the prep for this season. My plan is to remove the center section of the head liner and rebuild it...
  16. tpenfield

    1969 Mercury 7.5 HP Drive Shaft . . . .

    Yaaaayyyy . . . The drive Shaft arrived today I checked various dimensions with my digital caliber and it measures out as the same. I was a bit concerned since the parts are 11 years different and not called the same number. (45-39078 vs 45-95873) So, once the other parts arrive, I should...
  17. tpenfield

    1969 Mercury 7.5 HP Drive Shaft . . . .

    UPDATE: After much trail and effort to loosen & remove the retainer nut (aka bearing cover) I finally decided to drill into it and break it apart. . . making sure, of course that I could buy a new one. Here is the retainer nut all busted up . . . Disassembly of the lower unit was fairly...
  18. tpenfield

    Small Mercury Outboard Drive Shaft Removel Question

    I am trying to take the drive shaft out of the lower unit on my 1969 Mercury 7.5 HP outboard (serial # below in my sig). I have got the bearing carrier out of the lower unit and removed the bolt off the pinion gear at the end of the shaft . . . but the shaft does not want to come out. :noidea...
  19. tpenfield

    Bravo III . . . aahhh phooey !!!

    UPDATE: I have done a little work on the outdrives. . . . drained the starboard outdrive down and last night, removed the old bearing carrier and installed the new one. Here are a few pictures: Since I did a bunch of work on the outdrives last year, I have the tools and the bearing carrier...
  20. tpenfield

    Electro-Mechanical Trim Indicators

    UPDATE: I finished the second mechanical trim sender unit. So, now it is a matter of waiting until I have the outdrives back on the boat, and then I can install the trim indicators. Here are a few more pics . . . The 2 units . . . The mechanical actuators The electrical converters (slide...
Top