Search results

  1. C

    Evinrude 6 1997 Propeller shaft oil seal

    I would put the numericals 0336493 outside..for future referrence :-)
  2. C

    Evinrude 6 1997 Propeller shaft oil seal

    can't say... I never saw a double sided spring seal kind of 50-50 isn't it I hope the spring steel is stainless otherwise it will rust away eventually the inside one will soak in oil :)
  3. C

    Evinrude 6 1997 Propeller shaft oil seal

    spring side points inside the gearcase
  4. C

    Johnson 8hp milky gear oil ?

    well seems not to bad just refill but install new nylon washers on the fill screws and retry for a while next time dump the oil in a jar and wait a few days if water settles on the bottom it is ingesting water you will need a reseal job but some just keep changing oil every...
  5. C

    1968 6 HP Evinrude need help

    see book page
  6. C

    1968 6 HP Evinrude need help

    did you.. yes or no... Sorry to ask ... clean all orifices with a small wire .. carb cleaner blast all orifices then air blast to dry everything. check the side channel to the top drip chamber ... very small orifice to inspect and clean gasket type must be for the carb ...
  7. C

    Johnson 40e 74s blowing fuses

    in most... wiring layouts the fused B+ of the selenoid fat 12V post goes to the B terminal connection terminal on the starter key via side multi-wire harness. a) if so equipped , try just openning up the main side harness plug to see if the fuse stops blowing on its own without the...
  8. C

    3 HP Evinrude fuel supply problem

    assuming a JW18 or so most are all alike You cleaned the carb but.... did you or not....clean out the yellow HS supply install the fat gasket under it and clean out the HS jet & 2-3 side holes used to vaporize bubbling fuel ...... all with a very fine wire or monofilament to push out...
  9. C

    Evinrude 1993 20HP cutting out and needs choke

    vent open... ? does hand pumping help ? did you blow test the carb before reinstalling ?? air goes in upright NO AIR goes in upside down sounds like the inlet needle getting stuck shut ...
  10. C

    Carburetor Issue. Need help

    no need to change much ....try to locate an eqv. brass nipple if threaded if not threaded in the carb body thread the body for a matching nipple . or.... try to find just the plastic nipple
  11. C

    Looking for help, new boat owner

    see torque chart....
  12. C

    3 HP Evinrude fuel supply problem

    you don't need a new carburator $$$$$ did you read the link I sent you on cleaning the carb... ?? JW carb is a very simple carb... just unbolt the thing clean it up with carb cleaner ...don't use carb cleaner on the cork float !! blow out all orifices. why not visit utubes how -to...
  13. C

    3 HP Evinrude fuel supply problem

    if it runs with the fuel cap off the 2 holes under the vent screw are plugged solid.. look CLOSELY under for 2 small holes re: tank filter if plugged up you can just remove it and install a small gravity filter used on lawnmowers you need to check carburation and ignition ...
  14. C

    Johnson 50 in need of help!!

    start with checking carb bolt nuts, cover bolts etc.... look real closely for cracks apply temporary coating of grease to seal air leaks
  15. C

    Johnson 50 in need of help!!

    maybe crankcase vacum is not strong enough to properly suck in gas without the help of extra choking... 150psi... on the compression does nothing to help crankcase vacuum on the upstrokes . saw e utube where the mechanic used a propane gas torch to supply propane (unburnt) to...
  16. C

    '77 Johnson 70 hp coils

    as per the other post ... poking the plug boots to ground will tell you 1250 ohms or so and that is ok for IGNITION COILS.....
  17. C

    Boat won’t start, I’m at a loss

    could be just a frayed, shorted or broken wired A "set" of controls may be over kill $$$ if you can track down the impairement causing the problem test each wire end to end with a ohmmeter individually to confirm continuity then check each wire for any continuity with others in case...
  18. C

    1965 9.5hp johnson model # mq-11c

    if it was put to sleep properly it may be fine (oiled pistons, gear oil changed emptied carb etc...) yet 15years ages things...which can go wrong due to humidity, heat, mice rusted gear case you can always go fishing for more $$$ ....no harm is asking for more good luck
  19. C

    Boat won’t start, I’m at a loss

    check for any blown fuse in the wire harness under the side clip if ok ten.... holding the key on start.... wiggle shifter, cable harness, accessible wires ..... if nothing basic testing begins see basic/similar diagram 1978 and up check for +12 arriving at selenoid control post...
  20. C

    1965 9.5hp johnson model # mq-11c

    depends on condition...seized ?...cracked coils... salt water engine ??? impeller gearcase condition overall looks help generally a refurbish can hit 125$ for coils points condenser carb kit etc... I have paid $50-75 CDN for several 9.5hps this one a 1966 I paid $50 cdn . it...
Top