Search results

  1. C

    Recoil pull cord

    what I do is wind the cord with no tension in the rewinder ..then I pull the cord to load up the spring I jam the spool with the limp cord hanging out I then rewind the cord manually on the spooler a second time and release the spool this will wind the cord back in do it a few...
  2. C

    Evinrude 200 ficht

    have a friend hold the key on START ... . wiggle.. prod all accessible wiring.... jiggle shifter in case any neutral safety issues if you get a reaction ... bad cable or connection if trim works at least you have B+ to the PDP check fuses carefully ie: 10 amp...
  3. C

    Fuses in the Power Pak

    ?? and problem was... ??
  4. C

    Evinrude 200 ficht

    you are going to have to track it down with a volt meter recheck ( ohm TEST !!) all fuses on the PDP one 10 amp feeds the switch Some PDP (if you search google ) have bee known to have bad solder joints on the B+ input to the PDP they can be resoldered if handy with a...
  5. C

    Johnson 4R71D Resurrection Attempt

    has suggested pull cyl head ...then soak the pistons/rings a few days with wd40 , or plain kerosene alternate tapping the pistons may loosed them up use a one inch round peg and firm blows... not to hard ... alternate resoak a few days if need be if it clears up reinstall cyl...
  6. C

    Poor Idle Evinrude E50TSLECC

    thanks for your feedback on the idle chamber drip holes. I think many are concerned about popping out that little plug let alone peering closely with a microscope/magnifying glass to make 100% certain they are spotless ...something I will certainly look "into" next time I check one.
  7. C

    1994 Evinrude HE3RERM 3.3hp anybody know anything on this animal ??

    yep.. real cousins...AT my age I prefer oldies mid 50s to mid 70s ;-)
  8. C

    1994 Evinrude HE3RERM 3.3hp anybody know anything on this animal ??

    yes one set ... carb looks weird but it is a carb....
  9. C

    1994 Evinrude HE3RERM 3.3hp anybody know anything on this animal ??

    friend wants me to look at his motor. It is not the usual Oldies I work on. Even the ignition is to modern for me so hopefully just a good cleaning and point touch up will do it .
  10. C

    1957 35hp Johnson , Quits running.

    seems the hose was bad.....
  11. C

    Dura-tank Essence Fuel Gauge Crack

    in the mean time.... I would fill the crack with BONDIC UV glue and give it a shot of UV light for 3 seconds then paint it over with black fingernail polish :-) then look for a spare part in my...spare time ! https://notaglue.com/
  12. C

    18hp evinrude lower end

    ok it is filthy... but in gear...does it turn the prop if you turn the drive shaft or... is it totally stuck solid with rust if it turns refill with oil turn the drive shaft with a drill for 5 minutes or so (in gear F N and R ) dump the oil and inspect for metal chips, rusty...
  13. C

    1957 35hp Johnson , Quits running.

    if the fuel pump can suck enough to collapse the bulb the it must be working ok imho have you checked the fuel pick-up in the tank or changed hose ? . some hoses have a plastic like lining which gets to deteriorate over time. as to water ...find the leak but likely not...
  14. C

    2005 Johnson 15 hp 2 stroke carb float sticking open

    make certain any new gasket does not extend into the float movement zone inside the carb body... trim it if need be
  15. C

    Johnson 8hp sea horse 1985 idle diagnostic

    i think you have a good plan... clean the carb lncl the top idle drip chamber Should I remove the Black lever from the idle mixture screw in the pic in order to fully turn it 1 1/2? yes after the carb job... adjust LS with no knob....then install the knob mid-way of it's tr travel range...
  16. C

    JW-10 starts runs for a a minute or two then shuts off, can restart but shuts off quickly

    do the blow est with mouth air pressure blowing in the inlet nipple then turn the carb upside down to blow air . doing it manually by pushing on the needle against compressed air is not the usual way to do it. see if you can feel good suction on the carb face when cranking .. it is...
  17. C

    Can't figure out how to add trim fluid on 2007 Evinrude etec

  18. C

    Can't figure out how to add trim fluid on 2007 Evinrude etec

  19. C

    Can't figure out how to add trim fluid on 2007 Evinrude etec

    after refills..... cycle up/down several times... refill... cycle up and down 3-4 times refill to remove all the air
  20. C

    JW-10 starts runs for a a minute or two then shuts off, can restart but shuts off quickly

    if the impeller is ok and key is in it will cool itself but bubly water in a drum is like sucking coke in a straw.... the impeller can't pump bubbles.... try the motor in open water you can remove the filter in the tank and install a small lawnmower gravity filter between tank and...
Top