Search results

  1. R

    1983 25 HP Evinrude Shifting Very Stiff

    I think it was clearly stated that it is a remote controlled motor.
  2. R

    1983 25 HP Evinrude Shifting Very Stiff

    Propeller must be turned or motor running when shifting !
  3. R

    1981 Mercury 75hp water pump question

    I do not see a 75 HP listed for 81.----Serial # of your motor ?----Copper color decals ?-----I think an o-ring fits in that groove.----Best to get this correct as mistakes will be expensive.
  4. R

    2001 evinrude 4 stroke wont run over 2900 rpms

    It is a SUZUKI built machine.
  5. R

    1982 15 hp Evinrude pops out of gear when slowing down

    It likely wants to jump into neutral at speed.----But the interlock prevents that.----Time to investigate.----On many motors the clutch dog only goes one way.----Big $$$ for parts.-----Lots available used.---Your location ?
  6. R

    Merc 40 Force - Takes forever to start

    It is very easy to figure out why a motor won't start after 5 seconds of cranking.----Simple trouble shooting is a forgotten thing !!
  7. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    dremel tool.----Cut on 2 sides and seal might fall out.----Factory had special tools to remove seals.
  8. R

    Troubleshooting 1999 Johnson 225 HO

    Is there spark on all 6 leads , yes or no ??
  9. R

    Loss of power, won't plane

    Remove powerhead and check things out.
  10. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    the 59 housing would fit.----Along with the seal for a 59 model 10 HP.
  11. R

    80s Johnson 110hp does going into gear

    Saabu----You need to find a manual with a starting procedure for this and your motor !!----Pumping the throttle does absolutely nothing on these carburetors !!!!----There is no button to push in on his remote control !!!-----
  12. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    Part # of the seal you are installing?
  13. R

    Loss of power, won't plane

    Head gaskets are correct.----I am too far away to help with finding the blockage.----The saga continues.
  14. R

    1968 Evinrude 5HP Angler will start after a few pulls and run anywhere between 2 and 10 minutes then shut off.

    Did you replace water pump impeller ?----Did you inspect fuel pump diaphragm?-----Did you clean the carburetor ?------Did you replace head gasket ?
  15. R

    Loss of power, won't plane

    Post pictures of top of cylinder heads.------Showing the tabs on the top of the cylinder heads.
  16. R

    Loss of power, won't plane

    Water comes out of those hoses on the way to the thermostats.----When you start the motor water comes out those hoses.
  17. R

    1968 Evinrude 6hp - Gearcase Seal - Marred Prop Seal Housing

    You need to replace that bearing housing !!
  18. R

    1976 Johnson 9.9hp forward gear issue.

    It was clearly stated that the lower rod should be fully threaded in.----Just incase you questions the level of help here, I started working on outboards in 1968 and have more than 1 of those lower units on the shelf.
  19. R

    Loss of power, won't plane

    Fact----The water that comes out the tell tale does NOT circulate through the block.----You should have lots of water coming out of the hoses before the water visits the thermostats !!----Time to stop running this motor and find out where the blockage is !!!
  20. R

    Merc 40 Force - Takes forever to start

    It is an enrichment valve shown in the parts book.-----Not the same as a choke solenoid that pulls choke flappers closed.
Top