Search results

  1. R

    1994 Johnson 115hp, V4…Tilt Trim question?

    Folks will argue all day long.------At 95 PSI you have problems or a bad gauge.-----Good luck with it.------I can not provide any more help on this one.
  2. R

    running rough at idle

    If they are 1/4" screws then 100 inch lbs is correct.
  3. R

    1993 Evinrude 60hp

    There was a service bulletin in 1994 to move the telltale.-----So nearly 30 years ago.----I did not think there were any left that never had a proper service done at a dealer !-----The sudden bogging would be concern to me.-----Should not be hard to figure out the issue.-----Linkages loose maybe...
  4. R

    1993 Evinrude 60hp

    Recheck compression today.----Does hose for tell tale come off the side of the block or the top ?-----Install the lates water pump kit 432955.-----Comes with instructions.
  5. R

    1994 Johnson 115hp, V4…Tilt Trim question?

    On a new purchase like that the 95 PSI is a concern.-----Do not spend any time worrying about trim / tilt until you check / verify condition of pistons / rings.
  6. R

    1994 Johnson 115hp, V4…Tilt Trim question?

    Closed the manual release valve ???--Topped up the fluid ?-----Those compression values are not encouraging at all.-----I would be pulling a bypass cover ( 6 bolts ) on the 95 psi cylinder to look at piston and rings !!
  7. R

    1969 25 Hp Johnny Rude/Kicker?

    Pull the flywheel and check if coils are set correctly !!------They used that pinion and gear for over 20 years ( many models ) and there is nothing wrong with the design of it.
  8. R

    1969 25 Hp Johnny Rude/Kicker?

    Pull flywheel and see if coils are adjusted / set properly.
  9. R

    Honda 15hp question

    I do not believe the shafts use spacers.-----And parts availability might be an issue.----And this is a lot of work.---Sell it or trade for the motor you need.
  10. R

    15hp 4 stroke lower unit changing

    The gearcase would need to come apart to change out the driveshaft.----And step #1 is to check availability of parts.
  11. R

    1969 25 Hp Johnny Rude/Kicker?

    In my opinion there is usually no issue with those parts.-----I can not see or feel these parts on your motor.-----It should be a simple fix !
  12. R

    1996 90HP Mercury 2-Stroke - Plug Read Help Diag

    Does spark jump a gap of 3/8" on the three leads , yes or no ?-----Possibly running on 2 cylinders.
  13. R

    1969 25 Hp Johnny Rude/Kicker?

    Best to keep the 25 HP for that boat!
  14. R

    1978 9.8 Overheating

    Picked up a 79 model 9.8 yesterday.-----Nice looking motor missing a lower unit.----Have a few good lower units here.-----No problem to get it to run properly.
  15. R

    1969 25 Hp Johnny Rude/Kicker?

    The ignition on the 25 HP in 1969 is elegantly simple.----Separate for each cylinder.-----It runs amazingly well on 1 cylinder.----It tells your arm and shoulder when it is time for some simple maintenance.-----If you shop you can find a totally new ignition for around $100 or less.----On some...
  16. R

    Honda BF75 Hot and Weak Telltale

    Up to you to test with water at least 6" above the impeller.-----Too many exhaust bubbles means you will have trubbles.
  17. R

    1994 Mariner 9.9 issues

    You can likely find that arm on E-bay.
  18. R

    Honda BF75 Hot and Weak Telltale

    Running in a test bucket ?----Water must be 6" above the impeller.
  19. R

    1994 Mariner 9.9 issues

    Your location ?----Serial # of the motor ?
  20. R

    low compression #2 cylinder - 1988 suzuki dt85

    A very good option for you.------Keep this thread going as you make progress.
Top