Search results

  1. R

    Tubing, vents???

    Likely not much help to you today , but a factory manual has the hose routing diagram.----Sorry , I am not good at posting those pictures myself.
  2. R

    What part is missing???

    The motor is 65 + years old.-----I would think they used varnish / laquer when they made coils in those days.----Pull the flywheel and inspect.
  3. R

    Long distance commuters

    Even here around a small town the driving behaviour is getting worse.-----Speeding is a common place thing.-----60 kph here on my road.-----And I think an SUV went by at near 100 kph the other day.------Seems many folks just are not law abiding citizens any more.-----Then there is that fellow in...
  4. R

    Epoxy type to use in water jacket

    Can you tighten a bolt ( 1-4-20 ) in that hole now , yes or no ?----If you could tighten a bolt ( 80 inch lbs ) in that hole now I would not worry one bit about water circulation !-----Just fill it with JB weld and be done with it.-----
  5. R

    Epoxy type to use in water jacket

    If that was the only block in my workshop I would use an endmill to open that up.----Weld in an aluminum plug.----Drill and tap for the original 1/4-20 hole.-------Or I would simply replace the block from any number of parts motors.
  6. R

    Hard start and bogs in full throttle

    Have you checked for water in your fuel ?----Have you looked at the ----Link and sync----Procedure , yes or no ?------Do you understand how important it is for proper acceleration of your motor ?-----What elevation are you running at ?-------If fuel hoses are old and brittle , pieces can break...
  7. R

    1983 235hp Evinrude repower pros and cons...

    Agreed they were top of the line for a while.----People bought them because that was available at the time.----But today the computers and robots make these modern 4 strokes.-----Great running new motors.----- So complicated with miniature parts that they can't be fixed at home.
  8. R

    Combustion Problem?

    Go back to post # 5------A novice sometimes needs to clean the carburetor 3 or 4 times before it is really clean.----Easy to miss some of the small passage ways.
  9. R

    Unable to start and no water out the telltale

    ???----When pulling the knob out the choke flapper is CLOSED for cold starting.-----Why do you say---" opening choke for too long " ---here ?
  10. R

    1986 Johnson 30 water pump

    Do not use the bolts to pull it together.-----It should slide together.----Might help to turn flywheel a bit / prop / move shift lever.
  11. R

    Tubing, vents???

    What is the ---" backside "-----Of the engine.-----Post some pictures.--------Sounds like the oil recirculation system.-----Or part of the electric primer valve hoses.
  12. R

    85' 150hp driveshaft question

    Try------evinrudeparts.ca -----In Ontario.-----For possible help on used parts.
  13. R

    85' 150hp driveshaft question

    They had a ---" make room on the shelf " sale on them till they ran out.----$250 was last price.-----Down from about $2000 or so.-------Your location ?-----Good used is the option as you already know.
  14. R

    Engine removal

    The non power trim ( 6 amp stator ) V-4 models had a lifting bracket on the engine.-----I welded a piece of 1/4 flat bar to an extra flywheel nut for a custom lift device.
  15. R

    85' 150hp driveshaft question

    Those splines need to be greased.------Misalignment between lower unit and powerhead ( bent / warped exhaust housing ) can cause it too.-----Crankshaft is hardened steel. and not stainless.
  16. R

    Hard start and bogs in full throttle

    Sounds like throttle plates opening too early.-----And most motors rev up in neutral on a hose.-----Means nothing.-----Perform procedure know as ---" link and sync " on this motor.
  17. R

    what are these two holes in bilge area?

    Bad design is using wood as the structural element in a boat !!-----These drain holes are fairly common in older boats.---Just because water has a way of finding it's way under the floor.-------Wood in a fiberglass boat should be outlawed !
  18. R

    Mercury 402 40hp 1970s prop unit removal

    Sir James -----Your location ?
  19. R

    Cracked mercury powerhead

    Just run this motor.----Welding will not be the fix here !!!
  20. R

    Cracked mercury powerhead

    If the cast iron cylinder is not cracked I would simply run the motor.----Welding may make things much worse !!!----Did you have pistons out of the cylinders , yes or no ?-----Any pictures of pistons / rings ?
Top