Search results

  1. R

    1979 2hp Evinrude

    Your location ?-----If in Canada----evinrudeparts.ca-----may be able to help.
  2. R

    Need serial number help!

    ???---You have a serial # now-----Not sure if you will get help from BRP these days.
  3. R

    1979 Evinrude 2 hp 2902A torque specs

    Parts are available for these little motors.
  4. R

    1973 Johnson 50hp Will not get Full Throttle

    So with control box in full forward and maximum throttle the throttle plates are not fully open ?----How did it run for you last season ?------When / how did this happen ?
  5. R

    1970 evinrude lark 40

    Electric shift is wonderful and very reliable.-----Switch the 2 wires that go down into the lower unit and see if you get forward then.
  6. R

    Help 1980s 70hp evenrude Idles but bogs down under load

    If there is no spark the plug will stay clean.-------If there is way too much fuel the plug will stay clean.
  7. R

    1978 Johnson 70HP head scratcher

    I doubt there can be loose flywheel magnet on a 1978 motor.
  8. R

    1978 Johnson 70HP head scratcher

    Install new reeds , possibly new reed boxes and test run the motor.
  9. R

    Possibly ran without oil. What to check?

    Carburetors do not need to be installed in order to do a compression test.
  10. R

    Need serial number help!

    That number below the RPH would be the serial # of the replacement powerhead.
  11. R

    Evinrude Recoil

    The housing is listed as NLA.----If in Canada----evinrudeparts.ca ----might offer help.----Or there is Amazon and E-BAY.
  12. R

    Evinrude Recoil

    I believe Item #2 is a plastic pin and not the pin that the OP was asking about.
  13. R

    Need serial number help!

    Well-----RPH -----Clearly indicates that the powerhead has been replaced.-----Factory REBUILT POWER HEAD-----Hence the RPH.------Second picture shows a " casting number " that identifies the part it is on.-----Most parts have a 6 digit casting number.
  14. R

    1963 Evinrude 28 hp w/electric start wiring diagram

    I think Brad has left the building.
  15. R

    1961 Mercury 500 diagrams and resources, forward gear only

    You put the driveshaft in a sturdy vice on a bench.-----Use a 2X4 and a hefty hammer and drive the gearcase away from the vice.-----Unless it is severely corroded it should pull out.-----Pouring boiling water on the water pump cup area may help loosen it up.----Any pictures of reverse gear and...
  16. R

    Possibly ran without oil. What to check?

    There is a little item screwed into the carburetor bowls.-----High speed jet.-----( called orifice plug on the parts manual ) that item must be clean.-----Did you have it out for cleaning ?----It is way inside behind the drain plug.
  17. R

    1982 Mariner 50 HP Lower Unit oil leak.

    Do not need to look at your picture as I have seen this emulsion hundreds of times.----It is normal !
  18. R

    1982 Mariner 50 HP Lower Unit oil leak.

    Normal.-----You mix oil with the gas.----The oil has to go somewhere.-----Some oil / fuel mix goes right through the motor and is wasted.----I have often said that concept of 2 strokes and lubrication is not well understood..
  19. R

    2000 E15R4SSE /cooling problem

    Replace impeller and test run.----The oil does act as a bit of a heat sink..-----Have you checked parts availability on this motor ?-----Have you checked with a shop on their opinion and the popularity of this motor ?-----Have you done a compression test on this motor ?-
  20. R

    Oil use

    If this is an E-TECH motor then the computer ( ECU ) injects oil into the engine ( NOT into the gasoline ) as it sees fit.----Based on sensor inputs such as RPM and throttle position.
Top