Search results

  1. glennj3

    Setting two shift cables

    While waiting on more parts I got the shift shaft connected and now moved inside to the remote shifters. It may have been connected wrong. I refer to the shift lever. My shift lever has 3 holes in it, the bottom one is elongated (slotted) and the instructions say to attach the drive shift cable...
  2. glennj3

    I should just stick to doing what I know how to do, but....

    After spending a lot of money, lots of time working on my own boat, progress just sucks! So now I got more tools in, checked the inch lbs on my ujoint bearing. I can not tighten it enough to go over 2.2 inch lbs. I checked the torque reading at this point and it reads 80 ft lbs. I can still turn...
  3. glennj3

    what is the secret to getting the bellows on?

    I have spent 2 hours in the hot sun today, just can't seem to get the gimbal bellows onto the gimbal housing mount. I can only get it on half way, with or without adhesive. I don't understand why adhesive is used in the first place? I have a tool for the exhaust bellows, is there one for the gimbal?
  4. glennj3

    Replacing my exhaust bellows

    I have gotten the bellows off, at least 2 problems though I found no holes in the bellows. The shift cable needs replacing, at the outdrive the housing is rusted apart with rusted wires showing in the housing. I can get a new one, do I need a special tool to get the old one off? Next at the...
  5. glennj3

    Replacing all of the bellows for my outdrive.

    I am sure there must me lots of resources available to learn how to replace all of these but not sure where to look. I think I need to remove the outdrive, then start removing the section that the outdrive mounts to?
  6. glennj3

    Still can't get engine to take the gas and run smoothly

    I overhauled the carb, changed the timing to 6 from about 15 it was at. Removed the carb again, went through everything and put back on the engine. With the ear muffs on, she cranks up and runs so well. The idle mixture needle still has to be out 4 to 4.5 turns to run. She cranks up and idles...
  7. glennj3

    Shifter not in right position to allow cranking

    Recently and not every time, while in neutral, nothing happens. Put it in gear shift position neutral, and it works. Could the mechanisms in the back of the shifter handle just need some oiling??
  8. glennj3

    Timing marks?

    I decided to check my engine MC 165 timing before I consider pulling the carburetor off again. I believe I saw 6 degrees BTDC listed for it. I have the timing light and I can crank her up, so at idle, I need to ID the correct mark to use. Thanks
  9. glennj3

    Help with my anchor Pullpit

    My very old teak pulpit has seen it's better days. It measures about 23 inches long, is 10 inches wide at the base and has a 10x1 inch slit in the center for the rope to run through. It is two pieces of wood glued together.There are 3 bolts that hold it onto the boat. Thinking I may have to make...
  10. glennj3

    How can water get into the outdrive oil?

    Changed my fresh water impeller last week and found the oil somewhat milky. It sat up for a couple of years on the trailer under a shed. Was used just a couple of times since the last change and once this past week for a test run. I replaced the seals in the bottom of the lower unit about 3...
  11. glennj3

    Is my heat exchanger bad

    My post regarding my carburetor changed to having overheating problems so I thought I would just post a new topic regarding this. I removed my heat exchanger after doing a pressure test that would not hold more than 10 lbs. I do not have any pressure testing equipment here so I just filled the...
  12. glennj3

    Carburator adjustment ?

    Carburator adjustment 1987 470 Mercruiser, she sat up for about 2 years on the trailer under a shed. I put new batteries in, took her to the local shop, complete tune up and an old water leak repaired. They bypassed my fuel pump and used an outboard tank to run the engine. It still did not run...
  13. glennj3

    Skipping yesterday

    Last time I ran the boat 4 weeks ago, it hesitated to take the throttle. Before going out yesterday, it would not run in the yard, checked the points, they did not open enough if at all. Cleaned the cap and connections gapped them and she fired right up and ran fine. Got to the lake and started...
  14. glennj3

    engine wants to choke off when excellerating.

    Boat sat up about 3 or 4 weeks under my shed out of the water. She started off pretty good on the 4th but seems the more I rode the worse it got. Pulling a tube I did several stops you know. Sometimes it would cut off when throttling down to idle, but mostly when I gave it throttle she starts...
  15. glennj3

    What is the proper torque for....

    I replaced the exhaust looking gasket separating the antifreeze reservoir, the # 4 bolts are large I think 5/16 head. I put them at 40 Ft Pounds. Does this sound correct? Thanks, Glenn
  16. glennj3

    Why does oil smoke come out of the oil cap??

    My MC 170 had a plug type oil cap, this 165 has a cap with fiber inside and small holes around the lower portion. When driving I see oil smoke coming out of the holes and the smoke oil builds up and runs down the valve cover. Should I try and replace the cap with a sealed one or is this a...
  17. glennj3

    What is the best sealant to use on...

    My swim deck has a loose screw (as do I sometimes) it is also stripped (holds the braceing to the transom). I want to fill the screw hole with something that will hold it as well as seal it. Prefer something I can buy at WalMart or a local hardware store. Thanks' Glenn
  18. glennj3

    How to change engine oil

    I don't change my engine oil often because it is too difficult. I do have a oil vacuum apparatus I can drop a hose down the dip stick port but I just don't do that. I also don't like dropping oil into the well and catching it at the drain in the rear of the boat. Can't get anything beneath the...
  19. glennj3

    Suzuki Wet Bike repair

    Thought I would throw this one out for you. Maybe the wrong place to go but I need advice. My 19 year old nephew saw a movie of his mother (my sister) riding and falling off this thing long ago and he wants to get her running again. I have a very old Wet Bike by Suzuki. If you are not familiar...
  20. glennj3

    Inside area of engine compartment is rotting...

    I am considering repairing the wood that surrounds the engine, it is wood and was at an earlier time fiberglassed or resin primed. That has worn off. Wondering should I tear out the old wood and attempt to replace it with marine or treated wood and resin prime it, or just resin prime the rotten...
Top