Search results

  1. JASinIL2006

    Where to buy a new rear step ladder for a 1996 Larson 174 sei

    Re: Where to buy a new rear step ladder for a 1996 Larson 174 sei You just need the ladder part? I removed the flip down ladder from my 1997 Larson 186 SEI to install a different type. Is this what your bracket looks like: If this is what you're looking for, PM and maybe we can work...
  2. JASinIL2006

    dixie hustler "deck job" (turned full rebuild)

    Re: dixie hustler "deck job" (turned full rebuild) How was it covered before? Did it have any play? Before restoration, my tank was covered by a single sheet of 1/2" plywood, screwed into the fiberglass stringers and bulkheads. The only support was two 2x4s layed flat spanning the stringers...
  3. JASinIL2006

    Do you have firsthand knowledge of an I/O trim failing while trailering?

    Hi all, I've been reading all the perennial questions about using a transom saver/defloperizer, and it got me to thinking: how many of us actually have FIRSTHAND knowledge of an I/O outdrive tilt/trim failing catastrophically while being trailered? As often as this sort of failure is mentioned...
  4. JASinIL2006

    1985 Seaswirl Tempo 17 floor replacement turning into something bigger.

    Re: 1985 Seaswirl Tempo 17 floor replacement turning into something bigger. I forget who posted this originally, but I found it useful and I think it will help you.
  5. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider And here are the pics of the assembled interior! All that's left is to get the stereo to work (all I'm getting is a bass signal out of the speakers). Then, I splash her! View from rear seat facing the front of the boat: Rear seat and...
  6. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider Pics of attachment hardware for the sunpad (in response to a request from a PM). Port strut assembly (gas spring) viewed from the starboard side: One of two hinges (this is the starboard hinge): Top and bottom attachment hardware for...
  7. JASinIL2006

    Installing pedestal bases: 5200 or no 5200?

    Hi all, I'm getting ready to install the pedestals for my boat seats. They will be attached to bases I built and fiberglassed into the deck: The bases were attached to the deck after the deck had been glassed. Each base has stainless steel T-nuts to receive the screws from the pedestal...
  8. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider It's been a couple of weeks since I've posted any updates on my progress. I've spent the last week or two making all the engine connections and troubleshooting a problem with the engine. (It would turn over, but I wasn't getting any spark so...
  9. JASinIL2006

    Starting engine first time after transom rebuild

    Re: Starting engine first time after transom rebuild OK, Don, let's see if these pictures help... This first picture (below) shows the wires coming out of the ignition control module. (not pictured are the wht/red and white/green wires that go into the distributor): The next picture is a...
  10. JASinIL2006

    Shift shaft coupler not lining up correctly for re-install of outdrive

    Re: Shift shaft coupler not lining up correctly for re-install of outdrive This is what mine looks like with the shifter in forward: Here's a view of the shift shaft coupler from below: Not sure why it won't line up correctly...
  11. JASinIL2006

    Shift shaft coupler not lining up correctly for re-install of outdrive

    I'm trying to reinstall my Alpha One Gen II outdrive after a transom rebuild. I've been following the manual and I watched achris' excellent video on Youtube. My problem is that I cannot get the shift shaft coupler to line up straight fore and aft when the shifter is in forward; at best, it's...
  12. JASinIL2006

    Starting engine first time after transom rebuild

    Hi all, I just reinstalled my engine after a transom rebuild. I'm making the last connections and I'll be putting the outdrive back on next. Thanks to lots of help from folks here, the motor re-installation and alignment went pretty smoothly. My question: is there anything I should do as part...
  13. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider Got a lot done this weekend. I set up the gantry and my brother, my dad and I put the engine back into the boat! Ready to receive the engine.... My dad manned the hoist: Engine installed and alligned! Woo hoo! Trim pump installed...
  14. JASinIL2006

    Torque wrench for hose fittings?

    The Mercruiser manual stipulates certain torque settings for things like the hydraulic hose connections on the trim pump. I have a torque wrench with a standard 3/8" drive, but I cannot find locally any open-ended wrench adapters for that kind of torque wrench. I did find open-ended adapters for...
  15. JASinIL2006

    Getting ready to reinstall Merc 350 MAG

    Hi all, after rebuilding my transom, I'm hoping to reinstall my 350 Mag engine this weekend (have my dad and brother coming to help; they're pretty handy wrenchers with automotive engines and such). I've got the transom assembly (gimbal housing, inner transom plate) installed and I'm making...
  16. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider Got a little bit done today... I installed the gimbal housing and inner transom shield. Other than a bit of fun with the gasket, which came unglued, it went on pretty easily. Feels good to have it back on the boat. Torqued it down to spec...
  17. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider Thanks, all the fairing and sanding made the difference. I'm glad that is over! This isn't the best picture in the world, but you can get a bit of an idea of the texture.
  18. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider I also got the ladder ready to mount. Here's a side view of the test-fitting: This is the ladder stowed. I plan to install a strap to hold it down: This is the backing board I put in to support the ladder: It's really sturdy. It...
  19. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider Durabak is going on pretty well. The roughened stuff starts setting up really fast. I tried to use less accelerant, but it still gets clumpy pretty quickly. Altogether, though, it's not too bad to work with. It does stink, though. I've been...
  20. JASinIL2006

    Transom problems with Larson 186 SEI I/O Bowrider

    Re: Transom problems with Larson 186 SEI I/O Bowrider UPS delivered the new ladder today, so I'm going to try to reinforce the rear deck and install the ladder before I drop the engine back in. I'm going to reinforce the underside with a decent layer of hairy peanut butter which will glue a...
Top