Search results

  1. N

    Hmm...ok..1960 Evinrude 10hp running...

  2. N

    Points/condenser conversion kit

    And i do have that good timing youtube video saved when it comes time to install new components.
  3. N

    Points/condenser conversion kit

    Put that new fuel pump 388685 on, runs like a champ..my new points/condensers came today...haven't installed the ignition kit
  4. N

    Points/condenser conversion kit

    Put that new fuel pump 388685 on, runs like a champ..my new points/condensers came today...haven't installed the ignition kit
  5. N

    Hmm...ok..1960 Evinrude 10hp running...

  6. N

    Points/condenser conversion kit

    Hello I'm working a 1960 Evinrude 10hp Sportwin and in the process of replacing my coils , points, condensers. My question at this time if there is an conversion kit for my model can anyone please send me a part(s) numbers for both ways to go using standard approach or a conversion kit method...
  7. N

    Wide open stall, above 3/4 throttle...

    My real point is want to keep my oldy but goody going.. Do not wish to invest a life half savings into a now-@-days new outboard.
  8. N

    Wide open stall, above 3/4 throttle...

    All last few seasons seemed to run normal...just that do to and illness could not rin my boat from 2017 to present, no real issues but sometimes intermentant vibration like msybe a timing issue...somtimes issues would smooth out fine.. Pure like a kitten...ordered a retro-fit fuel pump...new...
  9. N

    Wide open stall, above 3/4 throttle...

    Old thermostat tested in pot of boiling water,seemrd to open and clos normally
  10. N

    Wide open stall, above 3/4 throttle...

    It was easy to locate from your sent diagram, old thermostat appeared never had been changed in its entire lifetime. Thermostat ring gasket had been torn pretty much thrashed. I need to order another thermostat/thermostat gasket and a thermostat housing gasket. Thank You
  11. N

    Wide open stall, above 3/4 throttle...

    Impeller seems to be working properly " peeing" out on both sides on lower half in a "Y" fashion...where would a thermostat be located on my particular model so i can run a check?. Thank You
  12. N

    Wide open stall, above 3/4 throttle...

    I own a 1960 Evinrude right aroubd 10hp, badge isignia states a model 10022 Havent run the motor in around couple years, fresh fuel, good blue spark. Noticed past 3/4 throttle after a minute or so engine begins to stall. Could this be a result of a weak fuel pump? Ive ordered a retro-fit pump...
  13. N

    Ignition kit for 1960 Evinrude

    I have a 1960 9.9 hp Sportwin model 10022 Am interested in someone sending me pictures or where to find ignition parts such as coils, condensors and points for my particular model. Also while im in here posting could use some info on a carb rebuild kit for my particular model. Thank You
  14. N

    1960 Evinrude 10hp fuel pump

    I am looking for a diagram to make sure ive reassembled my fuel pump back together correctly for my 1960 Evinrude 10hp Sportwin. I am aware that an retrofit model 388685 pump would be an option. Thank you
  15. N

    Ignition kit for 1960 Evinrude 10hp

    Can anyone tell me how i can purchase an ignition kit including points, condensors, and coils for this model?. Thank you
  16. N

    Retro-fit fuel pump

    I own a 1960 evinrude 9.9 is there an ip to date retro fit fuel pump for this model? Thank you
  17. N

    need a prop for Briggs & Stratton

    Looking for a replacement prop for a Briggs/Stratton Model 12Y602-0110-E1. Can anyone direct me to one or post a lin k?.. Thank You.
  18. N

    Biggs/Stratton 5HP Outboard

    Picked this up as a project to get running. Cleaned fuel tank. and system and was able to get it running. Runs well at just about half throttle and idles well at lowest throttle but after engine was warmed there was hard starting issues my guess needs a new fuel pump. The numbers of the metal...
  19. N

    Johnson Model FD-11

    Picked this nice Johnson FD-11 18 HP Seahorse up at a yard sale. Cleaned the fuel system and seemed to run fine. Impeller looked good, nice and flexible, but just stated it up again submerged in test barrel and it took a short while (after warm up) for the water to spray out of the exit port...
  20. N

    Ted Williams 5.5

    Bought at a yard sale recently and got it to pop and run but hesitantly, noticed fuel leaking from that pintle valve as well as around the float bowl of the underside of the bowl and maybe in need of a valve seat kit. Model number i come up with is a -59431 as far as i can make it. Engine tag...
Top