Search results

  1. D

    OMC vs Sierra

    What is the difference in the quality of the OMC parts and Sierra Aftermarket product. For example water pumps. They both appear to be of like quality but was wondering if anyone else had an opinion I know my OMC parts dealer does.
  2. D

    Pump looking thing

    What is the name of the part that looks like a pump. There is one on the oil line and one on the top of the jet drive. Looks like a pump you can push it in and it will flex back out. Made of flimsy plactic could be a diaphram of sorts but was wondering what it is called and what it is used...
  3. D

    Tiger Shark Piece

    1996 770 Oil leak problem while standing. Not the tank, redid lines, and fittings. Where would this thing leak oil other than the lines just setting. I also found water in the oil inline filter. When you blow back on the line you can hear air coming out the gas cap. This thing runs great...
  4. D

    1978 lean problem

    The hose that comes out of the bottom of the manifold and connects to the crank case. I found a big hose leak in that and when the motor coughs smoke comes out. What is the purpose or function of the that hose. I thought if was like an over flow for oil and if just put it back into the...
  5. D

    1991 OMC 35 has a cold

    The motor started coughing at idea. It gets better at higher RPMs but does not go away. Cleaned Carbs, good compression, and new plugs. What causes the motor to cough continually. Thanks
  6. D

    115 1976 V4 OMC

    I have a 115V4 but I found some 135hp V4 Carbs I know they fit but will I gain some hp. I have read several things on this some say yes and others say no. I did this on a 1987 90 v4 and it worked well as well as a 80is suzuki. Was just wondering. Also was wondering about a 35hp v2 replacing...
  7. D

    Awakining a sleeping giant

    Where is the post that shows how to properly start a motor that has been setting for several years.
  8. D

    1996 Tigershark oil leak

    1996 770 Tigershark. It is leaking oil while it is just setting. I was taken in and they said they fixed it but nope. Is there a common place these things leak oil while they are just setting. I have looked but cannot tell where it is coming from. Thanks
  9. D

    Wont crank at all

    1996 Yamaha 770 It set for two years and when it was put up it was a good runner. I will not even click. New battery cleaned connections. Checked the fuse it was good. Had power to the fuse and even checked power through the fuse. What next. Thanks for any help.
  10. D

    Yamaha 150 Four Stroke 2004

    The motor will not get up to WOT really just bogs down. Changed all the fuel filer even the one behind he intake manifold. Any suggestions. Also changed the gas. It wont get above 2500 RPMS will only just bog down. All the plugs look good all nice golden drown.
  11. D

    New Rod Bearings

    Replaced rod bearing and now it is hard to turn the fly wheel. Starter won t even turn it over. Any ideas...
  12. D

    Slack in a 60hp OMC

    1991 60hp OMC I had a clanking noise and have found it to be in the number two cylinder. When you pull the plug and spin the fly wheel by hand you can tell it is coming from that cylinder. I was wondering if it is caused by the wrist pin that connects the rod to the piston head or if it is one...
  13. D

    91 OMC 50hp

    91 50hp OMC has a rattle just above the cavitaion plate any ideas on what it is..
  14. D

    Slow Safe Question

    1997 150hp OMC. It will run good but once you get over 3600 to 4000 RPMS the slow safe will shut it down. Right before the slow safe activated you get a oil horn. My question is could it be the sensor in the oil tank or is the VRP pump going bad and just cannot keep up at that RPM. Would the...
  15. D

    70hp Tiller Kit

    I am attempting to put a tiller kit on a 70hp 1985 Suzuki. The tiller kit was purchased used. I understand the cowling pan needs to be replaced and have that also. The kit is used and a mess of wires. Any help would be appriciated even if it is a littel guidence. What parts do I need after...
  16. D

    Evinrude 150 Cuts out but resets

    1995 150hp Evinrude. The motor will cut out after running over 3000rpms. It will run for a few minutes then shut down back and just idle. If you try to run again it will not get back up and sounds like it is missing. But if stop the motor and kill the power it will jump back up then do the...
  17. D

    1986 Suzuki 70hp Tiller Arm

    I need help with the wiring. Does anybody have a diagram or know where I can get one. The kit was purchased used and is just a ball of wires. I would also like to test the horn on the tiller arm just to make sure it works if anybody can tell me how. Thanks dsinger@claremorecity.com 8)
  18. D

    silencing pad old orange spongy stuff

    Was wondering it anyone knows of a replacement for the silencing pad on the inside of the older cowlings. You know the old orange spongy stuff that falls all over your motor. The search button was messed up or I am sure I could of found some good ideas..
  19. D

    Power Pack ?

    Concerning the 75 76 and 77 OMC power packs.. On the three or six cylinder motors I noticed the packs wire up the same and are the same part number. I also noticed they both have four sensor wires but only fire three clinders. There is also one bank left open on the packs number 7. What are...
  20. D

    How easy it is to save money

    Made this in ten minutes with MS word and laminante paper from wal-mart. One on right it was the old one one left is the waly world replacment total price 15cents plus the clear coat on top to hold her in. This is minus the clear :^
Top