Search results

  1. M

    gear shift removal

    Mine did not need to be disengaged to remove button !! it just popped right off ... Maybe it was a fluke
  2. M

    gear shift removal

    First you remove bottom in center of handle " The throttle only button" Then remove throttle control with a socket after that you pry the cover shield off " the one that says quicksilver 3000" The screws for removing will be behind that cover !!!
  3. M

    2003 150 saltwalter water pump tube

    No problem glad to help!!
  4. M

    Power Trim issue

    yes my motor and pump are a set so the company sent me new motor and pump I still believe your system is low with air in it
  5. M

    2003 150 saltwalter water pump tube

    What's circled in red is the items in your picture
  6. M

    2003 150 saltwalter water pump tube

    Yes water tube bare copper . The rubber seal goes into the water pump housing and the plastic tube is a guide for the water tube
  7. M

    Power Trim issue

    I was referring to the $50 its like $109 and that only does them pump and trim rams not the main cylinder... Mine would do everything it was supposed to do except when it hit the 2 trim rams it would stop like it was hitting A brick wall instead of going completely down
  8. M

    Power Trim issue

    I just went through an issue with my trim after replacing the pump motor and I rebuilt my system and I can assure you that you will not fine a complete kit for $50.00 ... see my thread https://forums.iboats.com/threads/trim-o-rings.741946/ my issue ended up being the new pump that came with the...
  9. M

    finding tdc for timing

    That makes all the since in the world no rocking....
  10. M

    finding tdc for timing

    Thanks for your input ... helped alot apparently I was way off on the whole .462 idea...
  11. M

    finding tdc for timing

    I have a 200 hp off shore carbureted engine SN 0G693618 . The boat is new to me and its not idling correctly. I know the P/O was a tinker because when I mentioned it he said you just have to adjust this screw a little and pointed to the max spark advance screw ... so before I go messing with...
  12. M

    Power Trim issue

    loosen the bypass on the right hand side enough to push motor all way up then tighten it back up add fluid then lower engine with the pump and repeat until you can get the trim to raise the motor with out issue's
  13. M

    Roller bunk Adjustment advise ...

    It's a magic loader by magic tilt ... as far as something missing are you talking about on the circled bolts below? If so those bolts have to be lose to allow for the wobble rollers to move with the bottom of boat ...
  14. M

    Roller bunk Adjustment advise ...

    Ok thanks for the clarification...and yes I can get the boat off the rollers ...
  15. M

    Roller bunk Adjustment advise ...

    Here's a few more pictures these are the front rollers that need to be moved to get them off the strikes. In moving them outward this means away from the keel correct? Im just asking because that would put them towards the outside of the hull. some better pictures might help
  16. M

    Roller bunk Adjustment advise ...

    Yes the keel has about 10 inches.. and the back of the roller is even with the transom on the starboard side but the front of the boat is not centered in the trailer so I'm hoping that once I get it centered it will move that side back a little on the trailer.. if not I have room to move the...
  17. M

    Roller bunk Adjustment advise ...

    Looking for advise for roller bunk adjustment... in the pictures bellow you can see that I need to adjust the rollers on this trailer.. My question is should I move the bunks so that they are straddling only the 1 strike closest to the keel or should I spread the rollers apart and have them...
  18. M

    Trim O-rings

    I would love to find it for that
  19. M

    1987 150 xr2 trim tilt bleeding

    let me know how it goes I have been fighting this issue after I replaced the motor on mine here is a video of what mine is doing
  20. M

    Trim O-rings

    Lol its 109.00 for what you see in the picture
Top