Search results

  1. R

    Strange 1975? Evinrude 9.9 with cdi

    Looks close to 1982 decals to me.
  2. R

    Carb kit question

    There is very little that goes wrong with carburetors.---How is the motor running ?---Did you install a new water pump impeller last January ?-----What trouble shooting have you done if any?
  3. R

    Boat is stalling and primer blub sucked tight

    If vent hose is plugged you have bypassed that feature by opening the gas cap.
  4. R

    Boat is stalling and primer blub sucked tight

    The tank is vented when you open the cap !!----Recheck your work.----This should be simple to solve !
  5. R

    Boat is stalling and primer blub sucked tight

    Opining the gas cap vents the tank.-----The bulb collapsing clearly indicates a blockage between the bulb and tank.----Try another bulb ?
  6. R

    Boat is stalling and primer blub sucked tight

    Open gas cap ( temporary vent ) and see what happens.
  7. R

    Strange 1975? Evinrude 9.9 with cdi

    Rebuilt " new " factory powerheads came with electric start intake cover I think.----Post picture of the cowling if it has not been molested.
  8. R

    1997 Johnson Mod: J90TSLEUA

    Your motor is the 90 crossflow.-----So it is the 90*CV that you need.----LV is for a totally different LOOP charged V- 4 / 6
  9. R

    2 hp Johnson: My 2 HP Johnson is a model 2R78R a 1978

    I think you need to check your compression tester.----Or borrow / rent one and check compression on that 25 HP motor.
  10. R

    Oil Injection Pump

    Perhaps a hose , gasket or o-ring leaking.----Might be an easy fix.
  11. R

    Can a ballast resistor be added to a 1988 48 hp ?

    The charging system is only about 10 amp at full throttle.-----Why the concern ?----What type of battery in in your boat?
  12. R

    Strange 1975? Evinrude 9.9 with cdi

    Does not really matter as many parts were the same year after year.----But if you insist find your spares under a 1983 model.
  13. R

    Strange 1975? Evinrude 9.9 with cdi

    A rebuilt powerhead was installed.
  14. R

    '69 johnson hydro electric shift V4

    There is an o-ring in there to prevent leakage.---Even after honing.
  15. R

    Strange 1975? Evinrude 9.9 with cdi

    Post pictures.----Is serial # on transom bracket the same as on the powerhead ??
  16. R

    1997 Johnson Mod: J90TSLEUA

    Maybe remove the 4 bypass covers to inspect pistons and rings.
  17. R

    2 hp Johnson: My 2 HP Johnson is a model 2R78R a 1978

    The tester may have shown 65 PSI but there was zero pressure in the cylinder.
  18. R

    Shift rod adjustment Q-1972 25hp Johnson

    There is just 1 screw.----Adjust one way makes it better.---If not go the other way.---Fairly easy in my opinion
  19. R

    Shift rod adjustment Q-1972 25hp Johnson

    The shift rod does NOT turn on these.----------There is no adjustment at the brass connecter either.----So are the notches on the shift rods both lined up with holes in the connecter.-----The only adjustment is at the shift lever.
  20. R

    1974 Merc 9.8 hp

    Hopefully you installed a new water pump impeller.----If equipped with a plastic piece to open the throttle n, it might be broken.----I do not believe it is a fuel pump issue.
Top