Search results

  1. R

    Another Q about this '71 9.5hp

    It is all tied together.====Post the results of a compression test.----Pull flywheel and inspect the ignition coils !-----I gave heard it many times ---" I just bought this motor "-----I always start looking for the reason it had to be sold !!----If all is well with the motor , you must install...
  2. R

    Another Q about this '71 9.5hp

    How did this motor run for you last season ?-----Someone may have been adjusting that knob for no reason.
  3. R

    I recently purchased a 70 HP Merc of unknown vintage, The serial number is on a plate on the right leg of the mount. Help me figure it out please!

    A 1982 model , more pictures ?
  4. R

    1986 Johnson 150 HP Crossflow V6 Rebuild - Now What?

    Install the factory reeds.
  5. R

    1993 evenrude 70 hp compression

    As stated very common for #2 to be KAPUT.----The service bulletin came out in 1994 to move the telltale.-----But these motors are good and rarely need to visit the Evinrude hospital I think.
  6. R

    1997 Johnson 20hp

    Install a new impeller.---Test run again.
  7. R

    1995 25hp Johnson 2 stroke, what are the best years for the 25 hp?

    It is the same basic engine block from 76 to 2005 or so.-----Anyone from late 1980's would be my choice.
  8. R

    1979 Evinrude 70973R 70 hp Outboard

    Could be the exhaust covers leaking.-----A known issue with the 49 cube blocks,
  9. R

    1974 Evinrude 40hp ignition

    There are 2 posts on the ignition switch marked " M "-----To run the 2 posts are OPEN.------To stop the motor the 2 M posts are connected.
  10. R

    1995 Mercury 2+2 Help needed

    This motor only idles on the top 2 cylinders.----The bottom carburetors kick in at about 1800 RPM.
  11. R

    I’m at a loss - Evinrude 40

    Cheaper to visit a good shop and have them look at it.
  12. R

    1995 Mercury 2+2 Help needed

    Steps to take.----Nodody can see or feel your motor.----Need to know the compression values.----Post the actual numbers.----Does spark jump a gap of 3/8" on all 4 leads on a test device, yes or no ?----Replaced water pump impeller every 5 years ?
  13. R

    1989 Johnson lower unit compatibility

    Quite a few from 1979 to 1998 model crossflow V-4.----Your location ?----In Ontario , Canada try----evinrudeparts.ca
  14. R

    1974 Evinrude 40hp ignition

    Black plug.---12 volts is only used to energize the start solenoid and the choke solenoid.----The magneto under the flywheel generates the spark when it turns fast enough.
  15. R

    I’m at a loss - Evinrude 40

    And you were really convinced it was the reeds !!-----What trouble shooting are you prepared to do.----Have a fellow driving for 4 hrs for me to have a look at his motor.--2000 model 70 Johnson.------He has guessed at everything and replaced almost all the ignition components ----Wasted lot of...
  16. R

    Prop bearing cage

    Good luck with your project.
  17. R

    Prop bearing cage

    These units are easy to work on !----No alignment to be done if parts all look good.
  18. R

    89 Evinrude e25tecem

    Timing does not change unless the flywheel key sheared.----Post the results of a compression test.----You are running with fuel mixed at 50:1 in your tank ?-----Did you install a new water pump impeller when you bought this motor ??
  19. R

    Are cheap carburetors good?

    For marine applications it is foolish to try and save a few $$ on a carburetor.-----Any leaks to the bilge might mean you had a parachute on , instead of a lifejacket !!
  20. R

    Prop bearing cage

    Many folks have removed that pivot pin when trying to change the oil !!----That is a mistake.----If you are taking everything apart there is no need to worry when taking the pin out.----Did I say these lower units are easy to work on ??
Top