Search results

  1. R

    Prop bearing cage

    It is a pivot pin for shifter.----Take it out in order to take the lower unit apart.----Have a gearcase like that on the shelf here.----And one that is all apart.----They are easy to work on in my opinion !
  2. R

    1974 Evinrude 40hp ignition

    Stop !!!-----The coils on this motor do not use 12 volts from the battery to make spark.-----And I am working on a 1974 model 40 hp for the grandson.----New pistons and rings / water pump impeller / carburetor kit etc etc.----You may have done damage to points and coils if you applied 12 volts...
  3. R

    Prop bearing cage

    Yes , that nut holds the lower half on.---Along with a stud / nut at the front.-----You can pull that pivot pin if you are taking the whole unit apart.
  4. R

    1957 Johnson 18hp.

    Mark the hub and prop.----Test run the boat.----Inspect marks to see if they have moved after a slipping ( ? ) event.
  5. R

    !996 Johnson 50hp 2-stroke. No fuel through choke.

    The electric primer is a valve.----It is not a pump.----When you push the key in and crank the motor , does fuel come out the little hoses.---Yes or no ?
  6. R

    Overheating at idle, cool as a cucumber at speed

    Part is available all day long !!---And will be for many years.
  7. R

    1979 Evinrude 70973R 70 hp Outboard

    I can not see , feel or hear your motor.----Up to you to post some information.---Post compression test values.----Does spark jump a gap of 3/8" ( 1 cm ) on a test device.-----Does manual fuel pump go hard when operating it ?
  8. R

    Overheating at idle, cool as a cucumber at speed

    Couple of clicks on a Mercury parts site.---Listed at $33.95 factory quality.
  9. R

    Overheating at idle, cool as a cucumber at speed

    47-43026T is on the shelf everywhere !!!!
  10. R

    Prop bearing cage

    ??----What motor ?
  11. R

    Anyone know what control this is?

    What boat ?-----What motor is used on the boat ?
  12. R

    Old Evinrude question, Can anyone help?

    ???----Explain ---" bracket next to the impeller "
  13. R

    Theft Prevention Tohatsu 15 hp Outboard Motor

    Time to move.----I would not live in a neighbor hood of thieves !
  14. R

    Old Evinrude question, Can anyone help?

    Some folks use " clothes line " on them .----I looks the same but is NOT the same.----Use tiller cable from your local boat shop.-----They are ok for up to 40 HP or so.
  15. R

    Johnson 9R71R stop switch

    The universal magneto is under the flywheel.-----It is a wonderfully simple set up.---Reliable / easy to repair.----Coils are cheaper than they were 50 years ago.----Some will argue.----There is no need to improve that unit.----It was installed from 1950 to 1990 models !
  16. R

    raising transom on a boat for a long shaft.

    Your location ?----What do you mean " there is no parts for these " ?----You would have to change that exhaust housing.----So what would your budget be to raise the transom or shorten the motor ?
  17. R

    1957 Johnson 18hp.

    Post #3 clearly says to look at the rubber hub !!!
  18. R

    1989 25hp Evinrude compression release

    Charge the battery.----Load test the battery.----Take starter apart for inspection.----Check battery cables.
  19. R

    1957 Johnson 18hp.

    OOPS----I guess I missed that fact in post #1 about it being mounted on the same boat for 40 years !!
  20. R

    raising transom on a boat for a long shaft.

    If it has the 5" spacer it might be easy.----Post picture of your motor.
Top