Search results

  1. alldodge

    How can I make my Tracker 40 HP faster?

    Need more info to help the folks come up with what might be needed Is this a new to you boat? Is this a new issue or has it always run this way? What is the WOT RPM being seen? What is WOT speed?
  2. alldodge

    2012 3.0L TKS runs great with muffs, but slow on lake...

    There is no place to get a vacuum reading from this motor
  3. alldodge

    Radar tower removal.

    Normally there are access covers either directly below or above where the arch attaches.
  4. alldodge

    Need help: Bizarre Bravo III freshwater galvanic corrosion quandry

    In my findings aluminum is best for B3 and fresh water Also the amount of anodes used must be done with knowing the voltage reading. Adding more anodes will change the voltage readings, so more is not necessarily better
  5. alldodge

    Happy Birthday Aspeck

    Happy BD What about the Everybody want's to go to go to haven but nobody want's to go now?
  6. alldodge

    Rapid trailer jerk at higher speeds

    Closed
  7. alldodge

    Happy birthday Bob_VT!

    Happy BD
  8. alldodge

    Arghh! Freakin raccoon.

    Dad told me that in basic he got shots in both arms down the line and hatted the last one. The last shot was a cork screw needle that they twisted in and pulled out and it came out straight. Even when I went thru basic I still thought about that up to the last shot. Still miss him
  9. alldodge

    Arghh! Freakin raccoon.

    Ya sure that isn't a sea story? Maybe he missed :unsure: Here in KY they hunt Coons year round (except modern deer season), no limit with just a 22 and no one has ever said they needed something bigger
  10. alldodge

    Trailer Towing Capacity

    I have a ring on the 10 Ton Tag so have to use Pintle Have one of these to go into receiver
  11. alldodge

    Trailer Towing Capacity

    My thought also, the dump has more than enough tongue capacity. The class 5 list around 2700
  12. alldodge

    Trailer Towing Capacity

    Thoughts on towing Tractor, have 2 options Trailer, 10 Ton Tag with electric brakes and pintle hitch , plate list 10K pounds max, and trailer weight in 5500 pounds Tractor, M9540 no loader, weight list 5095 to 6175. Have methanol in rear tires 1997 International 466DT single axle dump with...
  13. alldodge

    Please help with HPDI issues

    For the most part yes Should the high pressure be between 675 and 720 psi? but listen to Boscoe99 he has a better understanding of your motor
  14. alldodge

    Please help with HPDI issues

    Welcome And to start, I have never worked on a Yam or Suz Running rich will blacken the plugs quick, and your posting shows it is No, most likely the fuel supply is running out so it starts to run with correct amount of fuel before it runs out of fuel Sounds like the power is being removed...
  15. alldodge

    Need help: Bizarre Bravo III freshwater galvanic corrosion quandry

    Never found a Marina that allows swimming off the dock. Also have never heard of a Marina do any testing unless the State requires it
  16. alldodge

    2012 3.0L TKS runs great with muffs, but slow on lake...

    He removed each plug wire and after each plug was removed it had the same amount of rpm drop
  17. alldodge

    2012 3.0L TKS runs great with muffs, but slow on lake...

    Timing There is nothing wrong with the valves with pressure this high. Might have some liquid in the cylinders but everything is within "spec", so that's not the issue Everything I read says there is nothing wrong with the motor
  18. alldodge

    2012 3.0L TKS runs great with muffs, but slow on lake...

    It's 2 ATDC, and does advance as manual states So everything works exactly like it should Sorry but I have nothing else to offer, I'm out of ideas
  19. alldodge

    Flat tire on haul-out today . . .

    ^^^ Agree just get a core. Pull one out of a new one and screw it in
  20. alldodge

    convert 2005 5.0 GXI to 2012 5.7 GIC

    Have not done this kind of swap but not to sure using an adapter 14 to 10 pin would be all that is needed. The motor uses a CAN bus and most likely will need the VP EVC display and cabling @muc As for the exhaust, if it will connect to Y pipe there should be no issue
Top