Search results

  1. Scott Danforth

    MerCruiser 3.0 to Omc 4.3 swop

    I would sell the OMC stuff and simply get another 1991 or newer 3.0 to get your boat back on the water. then in a year or two, get the boat you want.
  2. Scott Danforth

    No start with key

    have you checked the neutral safety switch? followed the yellow/red wire from the key switch all the way back to the starter?
  3. Scott Danforth

    OMC 400 upper gearcase bearing race spun

    most likely you also need the complete vertical driveshaft assembly too. that is a known failure point on the stringers as well.
  4. Scott Danforth

    OMC 400 upper gearcase bearing race spun

    I would first try to find a different housing. If that doesnt work, there is weld and remachine path or if the tolerance is tight enough, the bearing retainer compound
  5. Scott Danforth

    5056 rivets vs 2117tv rivets for 5052 aluminum hull

    Use 5051, 5083 and 5086 all the time. Have some projects using 7075 as well
  6. Scott Danforth

    In search for a 17 ft deck boat

    Winnebago also goes from flat to choppy quickly. Being shallow, the waves are close together. You can also run the Fox
  7. Scott Danforth

    Volvo penta stern drive longevity

    Most cases, old is better than new
  8. Scott Danforth

    Volvo penta stern drive longevity

    if its an AQ series drive it will outlast the hull, the motor and your great grandchildren with proper maintenance. For freekin real, no BS. 'cuz i dont have a new boat or drive to sell you. Now, if the drives were neglected, that is a different story. on the other hand, your 29 year old...
  9. Scott Danforth

    5056 rivets vs 2117tv rivets for 5052 aluminum hull

    5000 series aluminum is marine.
  10. Scott Danforth

    Need guidance on simple wire setup?

    any sealed VF4 relay (the good ones are only $5) https://www.newark.com/w/c/switches-relays/relays/automotive-relays?contact-current=40a&range=inc-in-stock|not-exc-nic I would run your hydraulic trim pump directly off the battery with a resetable circuit breaker. same goes for the bilge pump
  11. Scott Danforth

    Great time to sell a used boat.

    just look at the newbies coming here with their 45 year old OMC powered boats asking for help...... and they paid more money for those boats that were sitting in a field 2 years ago than I did for my Rogue. boats are selling, and way too many unsuspecting folks are paying.
  12. Scott Danforth

    alpha 1 gen 2 Speedo not wworking

    pull the hose and blow some air thru it. the passage is about an inch deep
  13. Scott Danforth

    staining wooden seats

    yes
  14. Scott Danforth

    Reputable boat & trailer shipper?

    as long as the trailer rolls, any car transport company
  15. Scott Danforth

    3.0 L lifter worn

    thats fine and dandy, however you cant just replace one lobe on a cam. you can attempt to replace the one lifter, and maybe you get lucky and the new lifter breaks in just fine and the cam doesnt eat it. however most likely, the cam will eat the new lifter you also cant swap lifters around as...
  16. Scott Danforth

    Why an increase in engine horsepower will hurt your ‘holeshot’, acceleration and midrange cruising.

    yes, that is the case. The other reason is it has been proven by aftermarket companies such as VSS on Volvo DP's for the past 10 years. bring the engine RPM's up by spinning the prop slower to get more bite to get the boat out of the hole, then switch gears to get more speed. same principle...
  17. Scott Danforth

    Great time to sell a used boat.

    unless you have your replacement boat, you may have an issue finding on to get back onto the water.
  18. Scott Danforth

    Why an increase in engine horsepower will hurt your ‘holeshot’, acceleration and midrange cruising.

    if you are building an engine for a boat, you must realize what you are doing. you want to increase low, mid and upper end torque. HP is absolutely meaningless since HP is torquexRPM/5250 you build an engine to increase the torque curve of the engine. the HP that comes out is a resultant...
  19. Scott Danforth

    Prop makes "clank" sound when shifting gears.

    are you shifting in water or on land with muffs? if on-land, that is the sound of the dog clutches banging into gear.
  20. Scott Danforth

    In search for a 17 ft deck boat

    i grew up on the inland lakes of Wisconsin as well as the shores of lake Michigan between Port Washington to Marinette, including the bay of green bay. Please specify which "Fox" lake you are talking about? the one in northern illinois, or the 7 in Wisconsin (including the one in Dodge...
Top