Search results

  1. F

    2021 Splash of the Year Nominations

    Mine WILL be done last year..... I waa going to ask who else splashed cuz i couldnt remember any others....
  2. F

    Second Happiest Day . . .

    What if you bought a big truck just for this trip and sold it once you got the yacht home and got something smaller for your daily splashes
  3. F

    Second Happiest Day . . .

    You kinda need to get the boat home before doing all the mods i expect you to do....
  4. F

    1974 reinell cuddy restore

    Also got windshield sealed and sky light window replaced. Now for advice...... Not sure how to do this headliner. Thin wood sheets with fabric or vinyl glued on and screwed in or foam glued to roof and glue fabric to that. Or any other ideas?
  5. F

    1974 reinell cuddy restore

    So i have not been idle... got almost all the electrical done, lights horn etc.... also got the hatch bow rail and all the deck hardare done outside. Got the dining table and rear seats/sun bed in also
  6. F

    Woke up this morning with a tree on the boat

    With your stri g of luck.... Might wanna remove dzaster from your name ;)
  7. F

    Fibergall & resin

    Oh and you cant gelcoat over epoxy
  8. F

    Fibergall & resin

    1st coat wood with resin to allow to soak in. If not the wood will absorb the resin as it cures and you will get a dry spot. With poly you need csm mat then the biaxial cloth. With epoxy just need cloth without mat. And once you got the hang of doing bits .... yes do bigger sections. Big...
  9. F

    aquasport 175 osprey

    Be safe
  10. F

    Multiple layers of fiberglass and laminating PE resin

    When i started my project i was getting my resin from a boat shop across from where i worked. Super cheap because they were a vendor and made good money on us... they would pump me out 5 gal buckets from their drums so i am sure it was fresh and they did alot of stuff there. That resin would not...
  11. F

    Remove quadrant gear and Stern leg is stuck in down position

    Here is my guess. After you removed quad and let it drop it must have hit hard on the 2 alignment pins and got wedged because it did move at some point. Loosen or remove side caps, loosen pivot bearing caps and lube with something. Attach (choke) a ratchet to the bottom of the outdrive leg and...
  12. F

    Remove quadrant gear and Stern leg is stuck in down position

    Edit...."without quad gear ON"
  13. F

    Remove quadrant gear and Stern leg is stuck in down position

    The quad gear is off. He cant get back on. Without the quad gear off it wont move regardless of fuses or motoer condition. Try loosening the pivot cap bolts a bit and gently pull on the bottom of the drive with a ratchet strap connected to something. It should move easy. Make sure ball gears and...
  14. F

    Immediate delamination

    Pee
  15. F

    Immediate delamination

    Must be cat ****...... That stuff ruins everything
  16. F

    Immediate delamination

    Is it possible there was a previous repair done in that spot with epoxy already? I had to do my bilge in epoxy due to a repair i couldnt grind out because i wouldnt have had a hull left in that spot. After doing the bilge i did transition pieces to isolate the epoxy and went back to poly
  17. F

    Tippy aluminum houseboat

    Could put them just above the rub rail.
  18. F

    Tippy aluminum houseboat

    What about "pontoon looking" fuel tanks wouldnt have to be very big either.
  19. F

    I think I'm another story of a bad boat purchase

    Agree about rot. Disagree about stopping project. He can make the cradle, start demo and grind away. Cut and prefit some of the wood. That way when it starts to warm he is ready to go glassing
  20. F

    1977 OMC Stringer running hot or ??

    Add to your to do list... Remove and test/swap thermostat
View older results
Top