Search results

  1. C

    Looking for old fasteners

    Gee, we used them to put thru the holes in paper, to assemble a manual. Those were more like #10, vs 1/4" though.
  2. C

    1986 Mercury 35hp Throttle/Spark Advance issue

    It is likely that the throttle arm will not move back to idle on it's own. The throttle cable is adjusted to push the throttle closed, and a bit of preload is added to help the operator feel neutral. The carb spring is only designed to close the throttle plate, not move the whole linkage...
  3. C

    1986 Mercury 35hp Throttle/Spark Advance issue

    The throttle itself is pushed back to idle by the throttle cable. The throttle cable should push the throttle arm against the stop, with some preload. However, the carbs have their own spring to close them. That is where you need to look.
  4. C

    Mercury lower unit cross reference

    SEI (Stern drive Engineering) makes these for the smaller Merc engines. They did not have your model number, but maybe one will work. https://www.sterndrive.cc/product/90-205.html
  5. C

    1998 evinrude 225 ocean pro, no spark! Help!

    You might get a factory service manual. marineengine used to carry them. Have your model number on hand. Do you have the optical sensor ignition? Are your coils in spec? This info and more would be in the service manual. On my '98 Johnny 150HP engine, battery power is supplied to the...
  6. C

    83' 115hp Mercury, prop slip

    Unlike Jimmbo, I have had very good luck with turning point props. I have 4 or 5 of them. You will want a 19 or 21P prop, likely the 19P prop would give better all-around performance.
  7. C

    83' 115hp Mercury, prop slip

    A cupped prop holds the water much better, allowing more trim and therefore more speed and efficiency. Check out a turning point hustler in 3 blade. They have good rake and cup and are high performance for aluminum.
  8. C

    Prop for Evinrude V4 crossflow

    Gee, you are comparing an aluminum hull with 3 steps to a fiberglass hull from the 70's? I doubt his performance is nearly as good as yours's.
  9. C

    83' 115hp Mercury, prop slip

    Do you have power trim? If so, you will want a prop with cupping, so it may be trimmed up to maximize speed. Actually, I am unsure if you can even get a new prop w/o cupping. What is your beef against it anyway?
  10. C

    New to me boat

    It would be unusual for a cockpit drain to have two scuppers on the same side. You might check them out and see what they are used for. I suspect one is for some other drain, maybe a fish well or something else.
  11. C

    Prop for Evinrude V4 crossflow

    Generally, motors of that HP on std boats cannot spin a large pitch prop like what you suggest. That is likely why you are finding them to be hard to find. 21" pitch is usually the max for them. Are you sure that your tach is accurate? Try Turning point props. They should have at least a 23"...
  12. C

    New to me boat

    Those are scuppers with one way valves. They can help if the scuppers go under water in a following sea, or if the scuppers go under water occasionally due to extra passengers, especially in the stern area. At rest with normal fuel load the scuppers should be above water. If that is not the...
  13. C

    Lost keys

    In the old days, the Mercury dealers had a key for each MerControl. We now have lots of aftermarket stuff. What do you have?
  14. C

    Conversion from I/O to outboard on Islander.

    The question is wether the transom will support that motor's power. I have heard, but never saw that the transoms of the i/o boats were intentionally made weaker than O/B models of that year. If that is the case those jackplates will damage the transom.
  15. C

    1990 yamaha 250 2 stroke seapro 2

    Gee, it sounds like you need a service manual for that motor. Who knows what else is not to spec. A service manual will have a wiring diagram for that motor, so you can get it right. Is that motor supposed to have an electric fuel pump? Most motors of that vintage had carbs and mechanical...
  16. C

    1988 Merc 70 HP wiring problems

    Since the motor does not use any battery power to create spark, the blown fuse suggests a bad wiring harness or a short. What is the condition of the wiring harness for the engine? A lot of them fail by now, if not replaced. Failing wiring harnesses can ruin the other igntion components.
  17. C

    Fuel tank

    If you have an ohmmeter you can check the sender, w/o seeing it. Disconnect the pink wire from the gauge. The pink wire should have some resistance to ground, say between 30 and 250 ohms, if it is good and connected properly. However, I find that the senders are the first to go. The last...
  18. C

    1978 Mercruiser 228 Sterndrive help

    SEI (Sterndrive Engineering) makes Alpha drive replacements however, I do not know the compatibility with your transom plate.
  19. C

    Jet drive for 22ci 25hp Johnson/Evinrude ‘69-73?

    Gee, don't you just bolt a bedpan to the bottom of the midsection? How hard is that (smile)?
  20. C

    Bottom paint

    Blisters are often caused by uncured resin in the hull mixing with water. I cannot tell from the photo what caused the damage you are seeing. However, I have simple topside paint on the hull of my boat, and it sits on bunks on a lift, and I do not have any blisters in the paint, and gelcoat...
Top