Search results

  1. jerryjerry05

    Question On Setting Timing 1993 90HP Sportjet

    Re: Question On Setting Timing 1993 90HP Sportjet Use a jumper or jump box to get past the neutral safety switch. The throttle needs to go all the way forward. Cranking speed is, plugs out, throttle open all the way(might need someone to hold it) key switch on. Then as the motor turns that's...
  2. jerryjerry05

    Yamaha Alarm System

    What signals should I get? Is it like the Mercury's. Intermitent tone=oil? Steady tone + overheat? My neighbors 2008 200 when the oil gets low it sounds a steady alarm. The pump under the deck for the oil works but when the tank on the motor gets low it won't automtically fill??The sender in...
  3. jerryjerry05

    Force 120 Stumbles - Runs Fine Wide Open

    Re: Force 120 Stumbles - Runs Fine Wide Open You said you " I thinned out the oil mixture a bit thinking that maybe the engine had picked up excess oil sludge in the bottom of the tank, and maybe I had added too much oil the last time i used it" This could have scored a cylinder or 2. Do a...
  4. jerryjerry05

    Chrysler impeller / water pump (70's) missing top plate & driveshaft stacking order

    Re: Chrysler impeller / water pump (70's) missing top plate & driveshaft stacking ord Re: Chrysler impeller / water pump (70's) missing top plate & driveshaft stacking ord Depending on the lower unit?? You might need a special muff?? The motor should be able to draw enough water to prime if...
  5. jerryjerry05

    Parts

    Hi all. I need the transom mounts for a 88/89 85/90/120/125 With the through transom bolts. I had a pair all ready to mount on my motor and I think someone collected them for aluminum scrap. EDIT I have a setup of 50hp trim/tilt. I'll try to post a pic.
  6. jerryjerry05

    Force 50 hp Lower Unit Leaking Oil & Water from Bolts

    Re: Force 50 hp Lower Unit Leaking Oil & Water from Bolts No the seal can be pulled from the outside. The oil can be filled at anytime,cold/hot. The unit will heat up and expand the oil and when it cools it will suck in water. If your gonna buy a kit cahnge all the seals. The iboats site...
  7. jerryjerry05

    1994 Force 120HP - Tilt/Trim not working, can hear both relays "click"

    Re: 1994 Force 120HP - Tilt/Trim not working, can hear both relays "click" Auto Zone or any auto parts store. Don't buy a cheap one. Get one with a long cord. You don't plug anything in. You hook the test light to any GOOD ground. Then apply the point to the green/blue leads as someone hits...
  8. jerryjerry05

    messed up fuel pump diafram replacement

    Re: messed up fuel pump diafram replacement They sell a gasket sealer that's gas resistant.maybe a small bead on the tear? The hole behind is the vacume lead for the operation of the pump. There is an X shaped gasket that fits there.#2 in the pic.
  9. jerryjerry05

    1987 Force 50 hp leaking fuel out exhaust and drain hole.

    Re: 1987 Force 50 hp leaking fuel out exhaust and drain hole. What's the compression #s? A clean plug is not good. Switch it around and see if it cleans the other. Like food says a clean plug is getting water or not getting gas? I had a head gasket go bad. Still had 145# of comp but had water...
  10. jerryjerry05

    88 50hp force not sure if water pump is workin

    Re: 88 50hp force not sure if water pump is workin The muffs are the one the 50 needs. The impeller can't be put in wrong. It will orient itself as soon as you crank it. If you don't have the right muffs you need to put it in a deep bucket. 90% of the water should come out the snout under...
  11. jerryjerry05

    Trim motor replacement.2002/125 Merc.

    How do you change the trim motor on a 2002/125 Merc? OT511345 It's reallllly rusting BAD.My friend wants to change it. And before I start, I want to know how to change it. Any U-tube videos? Thanks,Jerry
  12. jerryjerry05

    1987 force 50 hp- no spark in both plugs.... new to this motor and need help

    Re: 1987 force 50 hp- no spark in both plugs.... new to this motor and need help Get a spark tester.One that measures spark strength. Weak spark could be a loose connection,loose ground,wire under the flywheel rubbed through and touching? Shorted stator? Go to outboard ignition . com or...
  13. jerryjerry05

    Force 35 Hp Overheating

    Re: Force 35 Hp Overheating Your motor needs a special kind of muffs. The regular ones don't seal as good. They might work but might not. See the pics,this is what you should get/use.
  14. jerryjerry05

    Chrysler ignition switch wiring

    Re: Chrysler ignition switch wiring Not sure this will help.
  15. jerryjerry05

    85hp force cannot get flywheel off!!!

    Re: 85hp force cannot get flywheel off!!! I use black silicone.
  16. jerryjerry05

    My first boat and motor - 1993 Force 120 No spark from any spark plug

    Re: My first boat and motor - 1993 Force 120 No spark from any spark plug Try this,It might help?
  17. jerryjerry05

    Tools for Static timing.

    A timing light,a jumper or jump box. And someway to ground the leads. I'll get the directions and post them soon.
  18. jerryjerry05

    Trying to get rich off the unsuspecting.

    Watch what you see on the net. Defective.You'd have to fix it as soon as you get it. F660541 Force Outboard 85 125 Hp Power Trim & Tilt Pump Unit #(130864423829)
  19. jerryjerry05

    Pop...Goes The Flywheel!

    Re: Pop...Goes The Flywheel! You got lucky???? Some just "pop" right off some don't.
  20. jerryjerry05

    89 Force 50HP prop tangled w/ earmuffs

    Re: 89 Force 50HP prop tangled w/ earmuffs ANY!!!! nicks/cuts or abrasions on ANY splines or grooves will stop/slow the movement of the clutch dog. A small file,or even emory cloth smooth out the nicks. The clutch dog,it's gonna have some wear from normal use. If you have a shop or acces to...
View older results
Top