Search results

  1. jerryjerry05

    Help !! Volvo 3.0 Exhaust Riser Overheats

    Re: Help !! Volvo 3.0 Exhaust Riser Overheats If the riser's getting hot. Then the flow is blocked somewhere.Or it's not getting enough water. What drive? The drive has a rubber hose under the bellows that is connected to the drive.The connector#24 sometimes rot away/corrosion or electrolisis...
  2. jerryjerry05

    Diagram for tower shaft Force 120

    Re: Diagram for tower shaft Force 120 Here you go.
  3. jerryjerry05

    Chrysler 55 hp 1972 outboard motor wiring problem

    Re: Chrysler 55 hp 1972 outboard motor wiring problem Right pics
  4. jerryjerry05

    Steps to test the lower unit for leak & lower unit removal

    Re: Steps to test the lower unit for leak & lower unit removal Leak points: Do the leak test.Don't change anything unless you need to. Re-sealing might be more than you can handle.The bearing carrier needs a puller. You don't need to remove the shaft.The seals on the top under the water pump...
  5. jerryjerry05

    91' Bayliner w/ 91 Force 120hp L-Drive. Trouble gettin past 3800 RPM's.

    Re: 91' Bayliner w/ 91 Force 120hp L-Drive. Trouble gettin past 3800 RPM's. Air screw vs idle stop screw. The idle stop screw is where you adjust the idle rpms. It's on the bottom of the towershaft.Pic#2 The air screw,front or side of the carb.Is for adjusting the air/fuel mixture while at...
  6. jerryjerry05

    Newbie help with 1992 byliner and force 120 outboard

    Re: Newbie help with 1992 byliner and force 120 outboard At the tank.Near the filler or the sending unit is a sticker with the amount and construction info. Can't read that? Contact Bayliner,they are good about getting back with info. Or drain it and take it to a gas station and fill. 6 gal of...
  7. jerryjerry05

    Hey Frank

    Thanks for the vote of confidence!!!!People like that keep us rebuilder in work :) Jerry
  8. jerryjerry05

    Primer enricher/new model Force

    Anyone know the procedure for testing it? I did but haven't done it for a while and need to make sure how. There is a diaphram in there that can rupture.HELP!!!
  9. jerryjerry05

    Did I get the wrong part for fill, vent, and drain plug on 85hp Force?

    Re: Did I get the wrong part for fill, vent, and drain plug on 85hp Force? The stand is for the lower unit while it's off. The extra oil was probably from the extra water it took in. They heat up and cool down. Heating up expands the oil/metal and it pushes oil out through seals. Cool down the...
  10. jerryjerry05

    HEY FRANK poerhead swap 88/95

    Would a powerhead from a 88/85 work on a 95/90 ??? Thanks,Jerry
  11. jerryjerry05

    89 Force 50 Exhaust Gaskets

    Re: 89 Force 50 Exhaust Gaskets Yes That one.See pic #1 Not really that hard.Just take lots of pics as you go.
  12. jerryjerry05

    Did I get the wrong part for fill, vent, and drain plug on 85hp Force?

    Re: Did I get the wrong part for fill, vent, and drain plug on 85hp Force? I made this in about an hour. Works great!!! Don't buy anything other than the impeller. The new drain plug gaskets might fix the leak. Weep holes? Could it be unburned gas/oil? Any leaks from the top of the drive could...
  13. jerryjerry05

    Force Cooling problems

    Re: Force Cooling problems Untill you get a manual.Look up a parts diagram boats.net has good diagrams. Any parts you need can probably be bought on this site. If it sat for 6yr the impeller should be replaced. The gear lube is drained and filled from the very bottom of the drive.There is a...
  14. jerryjerry05

    Houston...we have a problem....any advice or help?

    Re: Houston...we have a problem....any advice or help? Might be as simple as a bad head gasket.Or a rebuild. After the inspection and you find anything BIG then swap to the back up. Can be done in a day if you have a lift. Removing the flywheel after 20 yrs can be tricky.See pic that's how I do...
  15. jerryjerry05

    Did I get the wrong part for fill, vent, and drain plug on 85hp Force?

    Re: Did I get the wrong part for fill, vent, and drain plug on 85hp Force? The drain plug is a small allenhead socket screw.On the bottom of the drive. Don't remove the screw in the little hole on the side of the drive.See pics, The white washer on the VENT/FILL screw can be replaced with the...
  16. jerryjerry05

    compression, 35hp, force

    Re: compression, 35hp, force Not all the carbs had that spring.See pic!! It might not be missing. I'd check the fuel pump diaphram. Install a small filter between the carb and pump. Tilting the motor will allow fuel to escape as the float changes position.
  17. jerryjerry05

    omc

    Re: omc If you have the drive with the cone clutches,it's the best one there is.I wouldn't change it.It's the same as the Volvo or Bravo's The shift mech can get corroded and stick.The cable can corrode and not work right. #21/42 is called the bellcrank, it and the rest of the mech can get...
  18. jerryjerry05

    Boat wont pee? 1986 Force 50

    Re: Boat wont pee? 1986 Force 50 The 50 needs special muffs.See pic.It will overheat with regular muffs. Just as a precaution replace the impeller.Then rebuild the fuel pump and check/replace the hoses.Install a filter between the carb/pump.J
  19. jerryjerry05

    Help diagnose problem with Chrysler Economate 3.5HP

    Re: Help diagnose problem with Chrysler Economate 3.5HP Install a sparkie in line.Then see if your not getting any spark.They sell these at any auto parts place.Some cheaper some more expensive. No spark,then the flywheel comes off and the points need cleaning/sanding. Remember it sat for a...
  20. jerryjerry05

    Quick question

    Re: Quick question #38 If it pulls to the right turn it to the right.As you look from the back of the motor..
Top