Search results

  1. alldodge

    NEED A VP PROS OPPINION!

    There is a Pro here but he has not shown back up for some time, and I for one miss his expertise It's a forum, so ya get a bunch of kinda sorta maybe stuff
  2. alldodge

    Correct spark plugs for an 888

    1979 is manual 3 OP has a 1976 and that is manual 2
  3. alldodge

    Correct spark plugs for an 888

    Hey ROY What ya shouting for ? Max WOT is 3800-4200 rpm
  4. alldodge

    Went electric

    Have Dewalt 18 and 20V several things. Picked up the 18 to 20V adapter and that was great. Old 18V skill saw would hardly make it thru two 2x4 before Bats were dead. Now a 5Ah Bat has never run out when using, so far that is Impact 1/4 and 1/2 drive, grease gun, drill, and latest is hand held...
  5. alldodge

    Correct spark plugs for an 888

    Manual 2 list to see note 5 Note 5 " 5/8 hex - 14mm plug - AC MR43-T except as follows: 888 (only), Serial No. 4615130 thru 4616217 and 4616217 and above AC R42-T 13/16 hex - 18mm plug - AC CR83-T"
  6. alldodge

    2000 Volvo Penta 5.7 Gfi with no spark

    Suggest https://obd2allinone.com/ecmrepair.asp It does not need to be from a 2000 model but does need to be programed for a 5.7 GSi Bob at OBD might have one, or can try offshore only wanted section
  7. alldodge

    Prime fuel tanks

    Also bleed the fuel rail by pressing in on the shrader valve
  8. alldodge

    Prime fuel tanks

    Jrato14 I moved your post to VP section, please don't post in the FAQ area Need to tell us what your working on If this is your 5.0 GXI-E mentioned in other threads then; have you pre filled the fuel filter?
  9. alldodge

    5.7 merc quadrajet idle

    That should have a bit of play
  10. alldodge

    Wiring my 14’ sea king from scratch….help!

    Don't see any reason to split the power, and motor that can be pull started in most cases you should not need to combine For a trolling motor I would use a deep cycle Typical wiring
  11. alldodge

    5.7 merc quadrajet idle

    No the primary Just want you to make sure the carb is fully closed against the idle adjustment screw
  12. alldodge

    5.7 merc quadrajet idle

    Not sure if you need a carb rebuild from your symptoms. If things remain as it was after cable adjust then maybe
  13. alldodge

    5.7 merc quadrajet idle

    Warm motor up and remove throttle cable and adjust carb idle to spec. Try to push the carb butterfly closed to ensure idle is set correctly. Adjust throttle cable barrel so cable just slides back on in place. Remove cable again and rotate barrel on cable one more turn out so when cable is...
  14. alldodge

    What model is my Maxum

    Maxum Marine was created in 1987 as a premium line to Bayliner boats. See post 3 https://www.maxumownersclub.com/forums/f17/hin-identification-help-6763.html
  15. alldodge

    Wiring my 14’ sea king from scratch….help!

    The Blue sea block gets only one hot and one ground. Each switch gets one hot coming from one fuse. The other side of the switch goes to the component your powering. The ground from the component being power returns to ground bus. Your motor charging system outputs 7 amps which will not be...
  16. alldodge

    What model is my Maxum

    There is something wrong with the HIN USH is a Bayliner The last 4 digits of the HIN is the date code month and year so yours should be Sep/1990 Most likely the model is the length so if it's 21ft would be something like 210
  17. alldodge

    Sea-fire alarm on start up

    ^^^Agree, it's the alarm sounding because there is no oil pressure. Older boats will do this unless there is a time delay relay like on higher end boats. Newer EFI motors don't do this because of the motors computer. A time delay relay can be installed to give you a few seconds
  18. alldodge

    2000 Volvo Penta 5.7 Gfi with no spark

    That is the cover, remove it
  19. alldodge

    4.3 GXI Pressure Test

    I would guess hoses are probably 5/8 ID, and if correct then I would use 1/2 inch SCH 80 PVC pipe, with solid cap. Find brass Tee and other fittings to connect schrader and gauge to PVC cap. Drill hole in cap then thread brass fitting in. Most raw water intake lines are 1 1/4 ID to the...
  20. alldodge

    What's the normal Carburetor Fuel PSI for an Alpha One Gen One 140hp Rochester 1985

    3-7 is normal range If you are actually getting a higher pressure then might need to change or use a regulator. Might also be the float level needs to be adjusted or issue with float needle and seat
Top