Search results

  1. C

    1958 Evinrude 7-1/2 Fleetwin carburetor overhaul

    sounds ok as a solution if you feel more comfortable.
  2. C

    1958 Evinrude 7-1/2 Fleetwin carburetor overhaul

    have you tried installing the clip vertically with the spring dipple on the outside face
  3. C

    Water pump 1962 johnson

    see video you change just the impeller but their is a new kit if you wnat to bring it up to date https://www.amazon.ca/Impeller-Repair-Evinrude-Johnson-Outboard/dp/B089SVRDCM
  4. C

    1958 Evinrude 7-1/2 Fleetwin carburetor overhaul

    use the old one
  5. C

    E-tec 40 hp

    I don't think your VST has an internal conical filter.. bigger engines have one on the injector return line. the external is easy to replace ... what is strongly recommended is an external fuel/water separator filter (RACOR 10 micron style ). I have used this seasence for 18 years ..no...
  6. C

    E-tec 40 hp

    be careful with battery switches, never use wing nuts etc... ETEC EMM,s are extremely allergic to voltage spikes.... EMM killers
  7. C

    1958 Evinrude 7-1/2 Fleetwin carburetor overhaul

    tell him you want 7mm strand solid wire core ... no carbon stuff.
  8. C

    1982 Johnson 9.9 water pump

    see pict similar shift link connector... rods must be properly inserted before bolting
  9. C

    1982 Johnson 9.9 water pump

    if you replaced the same size grommet it should be ok ... work the top end ... rotate the fw to line up the drive shaft splines. try shifting to raise the shift rod as you push up can you see the upper grommet condition uop the exhaust housing.. is it in place properly. flip...
  10. C

    1982 Johnson 9.9 water pump

    shift rod link properly mated. ?? do you have a borescope to look up the exhaust housing to see if the grommet is in good condition. try a dab of grease on the water tube. try turning the FW while to match the drive shaft and PW head patience brings joy...
  11. C

    1958 Evinrude 7-1/2 Fleetwin carburetor overhaul

    not if you just idle it... bucket tuning won't allow you to adjust things perfectly... just get it running then use a lake to finish up on adjustmenets
  12. C

    1958 Evinrude 7-1/2 Fleetwin carburetor overhaul

    just remove the prop... do not adjust the high speed in a barrel...even more so without a prop
  13. C

    1977 25HP Evinrude cutting out.

    just measure both boots to frame and they should be similar. swap the coils to see if the problem follows the coil or not.
  14. C

    Help! 1968 33 HP Evinrude

    pics please....
  15. C

    E-tec 40 hp

    try some chlorine mix...keep it away from carpets it may clean thing up....it works wonders on patio stuff grimy with black mildew. let it work in a few minutes whil keepng it wet . after.... a day in the sun with lots of UV can help.
  16. C

    Wits end again - 75 V4 115. Will an oscilloscope help??

    run the engine in total darknesss...see if you have arcing anywhere
  17. C

    Weird condition Johnson 55 hp

    keep soaking... patience brings joy...
  18. C

    Wits end again - 75 V4 115. Will an oscilloscope help??

    if you install a spark tester... the ones that flash ... you may be able to see which plugs are misfiring . you can then focus on that circuitry. plugs all good .. yes ?
  19. C

    Weird condition Johnson 55 hp

    with the left one installed and screwed down as much as possible have you tried a good hammer blow on the extractor bolt.
  20. C

    1993 Evinrude 60hp

    when I blasted the CdI it got significantly better and stopped surging. as a temporary option.... Any chance of trying the CDI it with some type of insulation from the engine heat .... something reflective or heat dissipating like a simple washer or two to reduce direct contact from...
Top