Search results

  1. alldodge

    Prop size

    Your WOT RPM should be 4600-5000 I would start with doing a compression test to make sure your motor is strong
  2. alldodge

    Need help with winterizing first boat

    Being a 18 footer it most likely does not have a fresh water system and your asking about the motor. If so need to know what motor and we'll move the thread to the motor section
  3. alldodge

    283 stalls when engine cover closed

    Flashback has same thought I do
  4. alldodge

    5.0 mpi mercruiser

    Your motor https://www.mercruiserparts.com/5-0l-mpi-alpha-bravo-0m300000-thru-0m5 The horn is most likely coming on because the ECM sees a problem. Not hearing the 2 beeps means the ECM didn't pass power up test Guessing it runs bad because the ECM can not read it's sensors. First look at 5V...
  5. alldodge

    5.0 mpi mercruiser

    Welcome What is the motor serial number? Clarify this statement Turn key ON and the pump does not turn on? Does this mean it doesn't turn on for a couple seconds and then turn off, or does not turn on at all? Does the horn turn on when key is first turned on or after 15 seconds? Once fuel...
  6. alldodge

    283 stalls when engine cover closed

    Does it die as soon as it's closed or takes a short time?
  7. alldodge

    Pumping out oil from dipstick

    OP shouted in first post no tube down the dipstick
  8. alldodge

    Best Sonar

    Need @dingbat and not getting much with sonar for under a grand IMO, fish finder yes but not sonar
  9. alldodge

    Pumping out oil from dipstick

    No problem with or without cap on, doesn't matter and is a non-issue
  10. alldodge

    Boat wont start

    Typical starter wiring and note this isn't yours it uses a slave relay which is posted above, yours is the square but wiring is the same. This start only If the starter solenoid shorted it "might" pop the breaker but in my opinion, it's upstream from the Bat. The breaker is there to protect...
  11. alldodge

    Boat wont start

    Post 1 Post 3 Post 13 Water in the starter is new The boat did run after it wouldn't start? Just guessing but maybe it got water in starter (water high enough in bilge) and then boat was run before this last thing started? Verify You have 3 relays and they are all the same type but have 3...
  12. alldodge

    350 Mag Bravo 3 with poor power steering assist

    Never had one move much at all once adjusted. The outer jacket should not move once nut at helm and cylinder is tight
  13. alldodge

    1999 Chaparral Sunesta 232 VP sx duoprop

    Also no O-rings on this one https://www.volvopentastore.com/Transom-Shield/dm/cart_id.768303287--session_id.485351959--store_id.366--view_id.782222
  14. alldodge

    1999 Chaparral Sunesta 232 VP sx duoprop

    Not finding any O-rings on the studs https://www.volvopentastore.com/Transom-Shield/dm/cart_id.768303287--session_id.485351959--store_id.366--view_id.775537
  15. alldodge

    Cobia 2019 237 electric head install.

    Welcome Nice work
  16. alldodge

    Fuel Pump Relay Tripped, now miss firing

    Must be fuel injected, and if so paint chips won't slowly die, it will cause it to miss. Might need a pump, but why not measure the fuel pressure to verify first?
  17. alldodge

    350 Mag Bravo 3 with poor power steering assist

    The tube is pat of the valve. It has slots in it that direct flow to left/right side as it moves in/out
  18. alldodge

    Fuel Pump Relay Tripped, now miss firing

    Sounds like it's running out of fuel What motor? Sounds like its a GL maybe, carb type?
  19. alldodge

    Fuel Pump Relay Tripped, now miss firing

    Welcome Watched the vid and motor starts and runs, did not see it die or try to stall. Did it die right after? Not seeing or hearing a problem
  20. alldodge

    Glastron tandem axle boat trailer question

    Most all trailers use the same bearings, races and seals. The only difference is the load capacity which determines sizes of the bearings etc. Go to etrailer, that have postings showing sizes of bearings and stuff based on load and spindle size. Once you know what the sizes are, then look all...
Top