Search results

  1. C

    58 evinrude 7.5 cooling problem

    One service bulletin from Evinrude # M168 says to remove the side plate when bucket testing & while removed .....also recheck for obstructions (crud) in the cavity and screen on the water pick-up when reinstalling the plate ensure opennings are facing FORWARD !! retest with a drill...
  2. C

    58 evinrude 7.5 cooling problem

    check the new pump housing it should have air passages to prevent air locks etc... or something similar clear all passages
  3. C

    2017 150 hp Evinrude lower unit

    http://epc.brp.com/Index.aspx?lang=E&s1=85165190-c305-4d8e-bacb-105d907c2e4b private seller or dealer sold ?? no warranty ? seller must have known :-( Try the ETEC owners group site maybe someone can guide you to a good used GC . SIte owner is a large ETEC shop ... may have used...
  4. C

    58 evinrude 7.5 cooling problem

    when did this issue start recently, suddenly, after repair work . ??? if you remove the PH (easy) you may be able to spin the drive shaft clockwise and see if water is coming up the water tube. it should ! IF not then you have the issue narrowed to the lower half of...
  5. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    poke a shiskabob stick in the cyl and find the high spot of the cyl. => TDC measure the points with a ohmeter and confirm the points just open at TDC . turn the fw and set the points at .020 recheck that points open at TDC with the stick ... you will feel the high point of the cyl...
  6. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    dang... morning cobwebs :-( Andrei... sell it !
  7. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    great.... I guess some are just more pointy or blunt see pict. what about the plugs do they look wet or dry when it dies ? inlet needle doing the job ? bulb get hard ??
  8. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    your HS needle is very pointy... seems they are usually more blunt than that certain it is the correct needle ? wild guess maybe fat donut in place ?
  9. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    see pics
  10. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    check for sparks (plug out and grounded ) across the whole range of the cam. spin it with a drill ....does it spark at all magneto cam positions ??? if OK the suspect a fuel issue then. it is drowning or starving did you try to adjust the HS needle since LS does not seem to be...
  11. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    how is compression ? maybe crankcase vacum leak reeds ? you can always sell it and get a nice 2 cyl JW :-)
  12. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    anything simpler would be called oars... check tank filter . float is not upside down is it ?
  13. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    great news ... if the motor (T&T) is not cooked it may be just in need of a rebuild. I had mine done 2-3 years ago I could not raise mine and it was just seals. keep everything greased up with regular upkeep !
  14. C

    Need help with 1968 1.5 HP Johnson model SC-10S

    old style carb going back to the 60's idling sucks gas from the top of the carb so that works :) higher speeds suck gas from the HS nozzle feed by the bottom HS needle. Have you tried openning up the HS needle a bit left (counter clock wise) ? Or... try closing the needle a bit in...
  15. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    good luck .. see your PM
  16. C

    Johnson TN-26 Fuel Mixture

    yes pretty certain... drop him a PM here and on the AOMCI site not certain but I think some folks have used o-rings ( find and fit them to size you may be ok )
  17. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    maybe.. this may help
  18. C

    Evinrude Etec 2012 150HP motor power tilt and trim stuck in down position

    Also check-in with these folks .... dedicated to ETEC support http://www.etecownersgroup.com/?forum=115573
  19. C

    Johnson 50hp Not cranking normally

    After checking the neutral switch if the problem still persists put the key on START and have a buddy wiggle the wiring all the way back to the engine . check any connectors for oxidation
  20. C

    Johnson TN-26 Fuel Mixture

    try removing the sintered filter for a test ... or you can install a small round filter for lawn tractors or similar on a temporary fuel line.
Top