Search results

  1. C

    1977 Evinrude 35hp Corrosion

    maybe... some high temp epoxies can be used just near the rims dents to help support the gasket surfaces https://www.amazon.ca/dp/B01IBOBY74?psc=1&th=1&linkCode=gs2&tag=1997ca01-20
  2. C

    1961 FD-15 Seahorse 18 HP

    water circulates under pressure and should flow enough I would not tear into a new gasket
  3. C

    ‘63 Evinrude 3302s 3hp questions

    and running in a barrel churns and aerates water... no good to cool a motor with !! try a lake run
  4. C

    ‘63 Evinrude 3302s 3hp questions

    is it hot all over or just around the exhaust which is not cooled like bigger models ? . in any event if new to you ...do change the impeller
  5. C

    Minimum compression on 9.9hp 1986.

    what is your feeling ..... it bog down at HS because it drowns in to much fuel ? anybody mess with the HS orifice ? (to big or damaged) it bogs down at HS because is lacks fuel ? clogged HS orifice ? inlet not doing it's job (sticky) float clip installed ?? it bogs down at HS...
  6. C

    Diapers and doggie pads

    Almost 14 years later diapers should not be needed for a mess but I do use those Dollar store doggie training pads under my outboards during maintenance ... keeps the floor clean :-)
  7. C

    82 Johnson 15hp wont start after run

    A blown diaphragm could flood one cyl but seems the other should fire up or at least burp with a shot of fuel or starter fluid ????? odd !!!
  8. C

    82 Johnson 15hp wont start after run

    https://forums.iboats.com/threads/2004-johnson-15-hp-will-not-start-after-motor-warmed-up.541708/
  9. C

    ‘63 Evinrude 3302s 3hp questions

    IF you have continuity to the coil possibly not but it can be a guessing game if the plug wire is broken in a bend somewhere under the plate. (can't tell from here :-) ) In any event to continue testing you must acquire test equipment like a VOM which is a basic necessity . until you...
  10. C

    ‘63 Evinrude 3302s 3hp questions

    fully remove the long "back corner bolts" on coils and 2 smaller base bolts next to the points. the plate will come out ... take pictures if you need to remember the back side of the mag plate wiring layout ! lining up the long coil bolts and 2 base retainer screws to the base...
  11. C

    ‘63 Evinrude 3302s 3hp questions

    well without conclusive /precise reporting of the outcome of testing... determing the cause of the problem can not progress to happiness. :-) btw ohm meters today are cheap and can be purchased for $10 .. it needs to be in the tool box to work on oldies. ! it can be as simple as...
  12. C

    ‘63 Evinrude 3302s 3hp questions

    do you have 4-7koms between plug boot and engine frame ? have the points been cleaned and adjusted to .020 ? are the coils lined up properly on their bases ? see pict. have you tried different sparkplugs set for .030 ? sad to say but some chineese coils have been known to be defective were...
  13. C

    ‘63 Evinrude 3302s 3hp questions

    points.... set the cam at the highest point of the lobe & the rub block adjust the points to 0.020 see link below for a more elaborate procedure but doing it has suggested is usually fine...
  14. C

    1998 johnson ocean runner 200hp j200txecm fuel bulb needs pumped at low idle or will stall

    one neighbor has the same symptoms........VRO issue ! fixed .
  15. C

    Evinrude 18 powerhead swap

    Hum... 50$ Realy seized or just stuck for some reason ? . Could be a gem or cheap parts to resell see my gem for $50 Cdn Evinrude 9622a $50 and was stuck hard
  16. C

    ‘63 Evinrude 3302s 3hp questions

    sparkplug boot clip and engine frame should have continuity between 4-7 Kohms http://www.pochefamily.org/outboard/Coils.htm if you remove the coils you should see the same 4-7Kohms between the high voltage pin and either of the 2 primary wires make certain you are using a...
  17. C

    1960 Evinrude 18

    for anyone interested visit the Western region AOMCI site for great articles (1-4) on condensers , how to rebuild them and how to test them with a home made tester (3 versions) . I built version one the simpler model and it works great . if you do want to build such a simple tester...
  18. C

    ‘63 Evinrude 3302s 3hp questions

    If I may..green coils likely ok condensers could be bad or points dirty secondary high voltage boot should read 4-7 Koms to engine frame make certain primary wires to the points do not rub against the moving parts (crank)...
  19. C

    1960 Evinrude 18

    for what you will why not just get keep it as a spare . If worried about the pollution (oil/Fuel) dumped overboard by the internal crankcase purge valve you can burn bio friendly oils . more expensive than wallymart stuff but friendlier. or... if really worried you could consider...
  20. C

    1972 evinrude 9.5 need long shaft or different trim?

    what is the mdl # of your 9.5 does it end with #3 like 9223
Top