Search results

  1. C

    1963 10hp Johnson QD-24 Flywheel rotating the mag plate

    see pic.
  2. C

    QD-22 - 1961 Johnson 10hp - idle help

    when you serviced the carb did you clean the complete low speed circuit incl removal& replacement of the top dime size plug to clean the 3 small drip holes. the idle circuit feeds gas to the top half of the carb by suction via a side channel which must be cleaned (use carb cleaner and...
  3. C

    Engine Does Not Crank - No Tilt/Trim

    https://forums.iboats.com/threads/no-power-to-start-motor-or-tilt-on-48-hp-johnson.745755/ see post#17... and others for fuse location
  4. C

    Engine Does Not Crank - No Tilt/Trim

    see similar case recently see text for fuse location https://forums.iboats.com/threads/no-power-to-start-motor-or-tilt-on-48-hp-johnson.745755/
  5. C

    Engine Does Not Crank - No Tilt/Trim

    where the main batt connects to the selenoid IN side follow the smaller wire (s) attached to the same post .. usually anyway
  6. C

    Engine Does Not Crank - No Tilt/Trim

    I believe... T&T relays and selenoid control are fed +12 via the main fuse did you check it ??
  7. C

    JW10 no spark problem?

    clean the points again and retest
  8. C

    Engine Does Not Crank - No Tilt/Trim

    buying parts on suspicions is a wild card ... probably a bad one.
  9. C

    1963 10hp Johnson QD-24 Flywheel rotating the mag plate

    I found tool rental shops have most sized you need because they have all sorts of gas powered tools to maintain. I paid about 20 Cents CDN a foot or amazon....
  10. C

    Engine Does Not Crank - No Tilt/Trim

    engine year model helps...
  11. C

    1963 Evinrude 28 HP Flywheel won't turn with plugs in (first ever outboard repair attempt)

    does it look like a mechanical .. or just high compression with plugs in do not reverse the flywheel... impeller fins turn clockwise like the fw you can drop the LU anyway to change your old impeller.. change the oil look for water .. and while the GC is down see if the problem is...
  12. C

    Johnson Evinrude 1980

    shifting cable adjusted properly ??? is this a new issue ? a new to you motor ? recent install ??
  13. C

    1973 Model 25302A 25hp runs great until the cover goes on

    experts here on that specific aspect may provide more info but your note seems to indicate a relation between the pump work and the consequence hence the need to review your work but... yes barrel testing will do that to as racerone points out !! you can always try a big fan to see...
  14. C

    1973 Model 25302A 25hp runs great until the cover goes on

    any chance you forgot parts sounds like the infamous 9.5hp problem of exhaust fumes working its way up to the power head and suffocating it ?? check of fumes under the cowl when it dies if so inspect lower housing and impeller work you did
  15. C

    Replacing rectifier 60 hp Evinrude

    never tried it but I do not see why it would not work and no harm should come since ac rectification will still proceed in 2 of 3 internal diodes. it is all a matter of design and capacity . the normally shared load of 3 diodes may... impose a bigger load on 2 of the 3 diodes. hard...
  16. C

    76 6hp seahorse dies after 10 mins

    is the vent open/working on the tank.... try with no fuel cap and see if things get better if yes.... venting issue to fix
  17. C

    Replacing rectifier 60 hp Evinrude

    3 yellows are for 3 phase ac rectification to DC if you had a 3 wires rectifier it is a plain full wave rectifier and those are dirt cheap on amazon...
  18. C

    XD50 vs XD100 in mid 90s 3 cyl

    A synthetic blend oil that delivers dependable performance under heavy use conditions. It also requires less maintenance. XD100 meets the specific demand of direct injection outboards and water-cooled 2-cycle outboard engines. More reliable, less maintenance. That's really all you need to...
  19. C

    1983 15hp Evinrude speed

    it will beat a pita Merc for certain !
  20. C

    XD50 vs XD100 in mid 90s 3 cyl

    with ETECs now manuf.disc. I guess they are dumping xd-100 for some reason
Top