Search results

  1. alldodge

    1" spindle trailer axles still sold anywhere???

    I think the 1 inch and 1 1/16 (1.063) is the same axle. The ID of the 1 inch axle bearing is 1.063
  2. alldodge

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    Block is drilled for 4 bolt but Mfg can use 2 bolt mains Same with cam
  3. alldodge

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    14093638 Manufacturer: Chevrolet Category: Engine Blocks Type: Small Block V8 Date: 1987-1995 Notes: 350, 2 bolt or 4 bolt, roller or flat tappet cam, 1-piece rear seal
  4. alldodge

    1999 5.0 Gi running fuel pumps off the ignition

    Its a safety thing, so long as nothing happens which probably won't
  5. alldodge

    Identify carb for rebuild

    I would suggest contacting carburator-parts.com which is Mikes carburetors. They will stand behind the parts and offer the info to find the right one I also found mentioning 75004-1 at sussex marine
  6. alldodge

    Boat winterized and summarized each year but not used in 5 years

    A 1994 should be a carb Take a 5 gal gas can and maybe 3 to 5 ft of gas line. Disconnect the line from the tank to the fuel filter. Attach hose to fuel filter and stick the other in down in the can
  7. alldodge

    4.3L GL-G Fuel Pump not getting power

    Not sure but think most are in line under some insulation. To check, use a ohm meter and see if you can get continuity from ALT to relay and Start assist relay to fuel pump relay
  8. alldodge

    Help with Battery issues after stereo install

    I would bet Red is main and Yellow is ACC
  9. alldodge

    Boat winterized and summarized each year but not used in 5 years

    If its "actually" been winter/summer then it gets ran and has at keast been run on 4 year old gas. That said it could also be there taking his money and not doing the work. If the drive is in the up position then boots need replaced, not that it wouldn't be a bad idea to do it anyway. Open...
  10. alldodge

    4.3L GL-G Fuel Pump not getting power

    Don't have the GL-G but have the E Choke is powered from a different tap then the pump Fuel pump relay is energized when the Yellow/Red is powered while cranking Once started the ALT powers thru the Green wire Check the diodes
  11. alldodge

    Mercruiser 5.7 V8 (1997) jumping RPM

    The sensor is under the distributor cap https://www.amazon.com/B-Ignition-MerCruiser-Thunderbolt-Distributor/dp/B0784MSV3P/ref=pd_lpo_2?pd_rd_i=B0784MSV3P&psc=1
  12. alldodge

    Mercruiser 5.7 V8 (1997) jumping RPM

    That's the TBV module and connector
  13. alldodge

    Mercruiser 4.3 LX won't turn over. Buzzer going off even with key off.

    Looks like you might have found the issue with the buzzer. It may be back feeding power s for the other power issue, I would remove both ends of both battery cables (do mean both ends) and clean them. Then find main power feed for the blower and other items and clean the power and ground
  14. alldodge

    Overheating

    Looks like one was the correct part, but so long as the ends were sealed all is good 27-48043
  15. alldodge

    1998 Merc 3.0l Front Engine mounting.

    Don't know how much sand was on top the lower half, but it appears sand and water made it thru the pump. On another thought, what does the engine coupler look like? Also rotate the drive shaft and verify it does rotate the lower
  16. alldodge

    1998 Merc 3.0l Front Engine mounting.

    Problem is the output tube from the pup was not connected to the upper half of the drive
  17. alldodge

    Mercruiser 5.7 V8 (1997) jumping RPM

    It can be a carb issue but rpm's usually don't jump around, they would bog and lag and then start picking up speed again
  18. alldodge

    Mercruiser 5.7 V8 (1997) jumping RPM

    Then the motor doesn't match the serial number. A cam sensor is a EFI motor.
  19. alldodge

    Inconsistent bogging/acceleration until it hit around 20mph - Mercruiser 5.7l

    The pic above is that of a chevy car/truck motor so its showing the fan. Orientation is from the distributor, and No 1 is port side closest to the bow
Top