Search results

  1. alldodge

    V drive noise

    Vid doesn't work There should be no noise while in gear. Can be a slight rattle in neutral at idle if the motor is not firing real smooth Unable to find specs (have install and repair manual) on each Walter model. The 26 is not as beefy as the 50. If boat cam with 26 then my thought is, one...
  2. alldodge

    Electrical diagram ss18

    W and W/O Reg
  3. alldodge

    Penta D6 White smoke and coolant loss

    Depends on how bad the leak is. Not seeing how the HX or Turbo would induce AF in the exhaust. The HX has raw water on one side and AF on the other. If HX leaked then AF would leak into raw water side because pressure would be greater. Turbo has exhaust but only thing to leak into is oil...
  4. alldodge

    Fuel Delivery/starvation Help troubleshooting

    Is it MPI or EFI? I'm thinking electrical, so I would start with the 10 pin engine connector. Then the rear of the block where the Negative battery cable attaches and should also be engine harness connections. Feel along the engine harness and find any grounds which come out from it to ensure...
  5. alldodge

    3.0L hard starting when warm

    Less then 90* it is open, it's open at 118 and closes at 119. My comment was if it closed at 110 I wouldn't replace the switch
  6. alldodge

    Mercruiser 3.0 only stays running with key engaged?

    OK the old one Don't know about the yellow. Normal would be black for Dizzy and Gray for Tach The purple may be the resistance wire and if it is, it may need to be connected to the electric choke. Need to trace that wire to determine where it goes to.
  7. alldodge

    Mercruiser 3.0 only stays running with key engaged?

    My guess is wiring is not correct. The 99 harness would have only one wire which would be purple going to the + side of the coil. Points wiring would have 2 wires on the + side of the coil. Purple/Yellow coming from the starter solenoid and a Purple resistance wire coming from the electric...
  8. alldodge

    Volvo 8.1 DPS outdrive

    Could ask @GA_Boater to get your access back The noise is gimbal, U joints or both. Pull the drive and it can be determined.
  9. alldodge

    3.0L hard starting when warm

    Agree its bad, but it list 110 +/- 8 which means it should be open between 102* to 118* If it closed at 110 but was open at 111* I wouldn't replace it Edit: agree I misspoke at first
  10. alldodge

    Mercruiser 3.0 only stays running with key engaged?

    Went from electronic to points ignition, are you using the 1999 harness or the older motor harness Just get a ballast resistor which would read 1.8 to 5 ohms. This will provide the coil with 9V when running
  11. alldodge

    Mercruiser 350 poor performance

    You can find a bad impeller but blades coming off immediately need to check your housing and what impeller your getting
  12. alldodge

    3.0L hard starting when warm

    Switch is item 32 https://www.mercruiserparts.com/bam/subassembly/30906/11669/40
  13. alldodge

    3.0L hard starting when warm

    The temp sensor is a switch on/off. Put in water and heat it up. Manual shows If the coolant temperature is above 43º ± 3º C (110º ±8º F) the switch should be closed
  14. alldodge

    3.0L hard starting when warm

    The ring terminal is most likely used for something else that could be installed but wasn't like a Mercathode. Being black it should be a ground
  15. alldodge

    3.0L hard starting when warm

    The one on the left is alarm - Tan/Blue wire The one on the right is the gauge sensor - Tan wire Test gauge sensor but putting in a pan of water. Connect ohm meter and heat it up
  16. alldodge

    Mercruiser 350 poor performance

    The Reg is behind the motor mount on top. My guess is you have a 30 psi system. Could try to pinch closed the return fuel line going back to the filter. Do this without the motor running just cycle the key. What your looking for is to find out if you can get the pressure to go up to 50 psi...
  17. alldodge

    Electrical diagram ss18

    Not going to find a boat diagram. There would be a motor diagram, but need to know what motor?
  18. alldodge

    Vacuum Gauge Connection

    Kids
  19. alldodge

    Delco voyager conversion

    That's good Then just the one connection between Dizzy and coil. Then just needs power from purple to run. The other connection on the coil would be for the Tach but its not needed to run
  20. alldodge

    Vacuum Gauge Connection

    Thanks I understand The big IF unless someone has an answer is to find a plug on the intake. If there is one on one of the intake runners then plug can be removed and fitting installed. If not, then its of no use. Could use a Tach but agree not as good for idle as a vacuum gauge
Top