Search results

  1. R

    1974 Evinrude 25hp wont run.

    Are we sure the gap on a J4C is 0.020" on this motor ?
  2. R

    1970 25hp Johnson lower paint question?

    Paint colour is listed for 98 at---evinrudeparts.ca-----And many other sites.
  3. R

    My 1974 Mercury 150hp Hard Starting Issues

    The inline 6 is a wonderful motor if in good condition.----As stated some folks think they are junk !------So good luck with it.
  4. R

    Unknown 55hp Johnson boat restoration

    Don't spend any beer tokens on the lower unit / engine until you have a boat that you can safely use.
  5. R

    Help Identifying evinrude 150 or 175

    We do not know if a " low compression " kit was installed.------But these motors have a history of broken rings.----Post your compression values.
  6. R

    My 1974 Mercury 150hp Hard Starting Issues

    The Johnson / Evinrude primer will make hard starting a thing of the past.----Time to take starter apart as well.----Slow cranking is also an issue on these wonderful motors.
  7. R

    Evinrude 6 hp mystery

    Well----Electronic ignition was first used on the 77 models.------The decals clearly indicate a 77 model !
  8. R

    Evinrude 6 hp mystery

    With electronic ignition it is a 77 , 78 , or 79.----But correct , the decals say 77.
  9. R

    My 1974 Mercury 150hp Hard Starting Issues

    Install an electric primer valve as found on Johnson / Evinrude motors from 1980 to 2005.----Simple and reliable.----Squirts fuel into the motor like you are doing now.----Does it at the push of a button.-----Lots of good used ones available.
  10. R

    Help Identifying evinrude 150 or 175

    Not a 150.----Could be a GT 175 from late 1980's or an earlier 235 HP based on the " bubble exhaust " cover.
  11. R

    Help Identifying evinrude 150 or 175

    Well----What kind of motor is this on.----2 HP or 300 HP ?----Post some pictures of this motor.
  12. R

    Pontoon boat Engine too low?

    Have you tried another prop ?----The hub could be slipping.
  13. R

    How would you do this transom?

    The structure under the floor is likely rotten too.-----Do a complete evaluation of boat / motor before spending any more beer tokens.
  14. R

    Mercury 9.9hp 80's?

    My wildest guess is a 1994 model.----But a dealer would insist on the serial # to get you the correct parts first time.----Online parts places will ship what you ordered.---Right or wrong parts.
  15. R

    Fix it videos

    Saw the same the same feller apply plenty of gasket sealer on the intake gaskets.-----He likely blocked off the oil recirculation channel.---I doubt he even knew the channel was there.------If a little bit of sealer is good , then lots must be better.----What a joke !!!
  16. R

    1969 55hp Johnson

    So is that how you had it ??
  17. R

    '87 Johnson 50hp VRO(deleted) Idle speed issues

    if engine runs cold it may not idle properly.
  18. R

    1969 55hp Johnson

    The large post goes to the cap.----The smaller post gets the wire ( blue ? ) from amplifier.
  19. R

    1969 55hp Johnson

    ???----The rotor has a key on it that must go in a notch on the crankshaft.-----Back firing indicates timing off or plug wires on the wrong plug.
  20. R

    1969 55hp Johnson

    The flywheel key sheared on that motor has nothing to do with spark or timing.-----Compression should be 140 PSI + on that motor.-----If you put gas in the cylinders it should bark like a wild dog or roar like a lion.---The rotor key is in the right place ?
Top