I think it rusted out, can see the edges of what's left of the plug and appears to be steel. Check the ones on the block and see if they are brass. Could be someone replaced the block and used steel plugs. Clean it up and fill it up to see if there is other leaks.
Not understanding so what I'm saying is both the 2.0 and 1.65 uses the same gears in the upper section 24/24 gears. The ratio is changed in the lower. The 2.0 uses 14/28 gears and the 1.65 uses 13/21 gears.
If you are using your same lower, either upper (yours or other one mentioned) then you...
Don't know what a spit back valve is but the take will have a vent line attached which gas can spit back if not installed correctly. Note the vent line should have no loops in it where gas can get trapped in it. If gas gets trapped there will be no place for the air to come out.
My Rinker...
User name not always showing up in upper right corner. Sometimes it does, other times its just blank, and other times name and cart but no avatar. First I thought it was just when there were no messages waiting, but found that to not be the case. The way to see messages I select anyone's name...
Replacing parts is easy enough to explain, doing it takes some work.
Before getting into that, why does the rudder need replacing?
Pulling the prop takes removing the carter pin, remove nut and then need a prop puller. There are different sizes and depends on size of shaft and prop. An...
Yes, that is the correct size, when new its not that tight, after being on for a while with double clamps it is hard to get off
This is a shields piece of hose which I used on my boat
It can be one of 2 types and depends on what your serial number is. The original type was a barbed fitting and newer style used a snap lock fitting. Merc part number 32-8M0062666 and the hose is standard hard wall hose 1.25 ID. Look for shields 16-250-1140-12 as the part number and is sold by...
I have not, but it must be true because the police have said it is, then that is the way it is.
Suggest contacting NJ DMV or who ever does boat/trailer licensing and ask for the regulation. The reg should state what is expected/needed
Thinking the trailer is like a long Tee, maybe it just...
If the transom plate is at an angle and not parallel within 1/8 (2mm) to outer surfaces, this will keep it from aligning within spec.
When installing motor, was the rear bolts installed snug, motor lifted up off front mounts just bearly hanging from the thermostat housing. Then lower front...
Agree check power at the coil in run
Also disconnect the shift interrupter switch just to rule it out if it is casing any problems. The switch should not be the issue, but disconnect it just to remove a piece out of the equation
If you have 2 seals, I would recommend using the new style seals which are a double seal, part numbers:
1 each Small inner seal 26-8M0033407 (replaces 2 each lip seals)
1 each Large outer seal 26-861694 (replaces 2 each lip seals)
Dimensions 3 - 3/8 OD, 2 - 1/2 ID, 13/16 wide
You...
In general accelerator pump and choke plate arms are adjusted by bending the arms/rods. Things like tangs are bent for certain idle stops and/or floats
If the VP is wired like the Merc (probably is) the pink, pink/white are ignition power and injectors are batch fired (4 at a time). Ground is applied by PCM
Could be VP uses 2 different fused feed lines to power each side. Look forward to MUC input
Merc type which uses all pink/white
None of your diagrams will work, only one that can be used is on the left and it will only work to start the motor and run boat electronics.
This setup will do what you want without a switch, but keep in mind it will drain both bats when trolling. If both are drained to far, then there is a...
It sounds like rod bearing until the rpms come up, then when the noise should get worst it starts going away. Post a vid of the motor just idling.
Check the firing order 1-3-7-2-6-5-4-8
Grand kids are all great, I have 6, but yesterday got my first great grand baby. Her name is Genesis
Told my friend I'm now great at something :D and he replied ahhh no your not :(, might need to rethink my friends list
