Search results

  1. alldodge

    2005 Mercruiser 5.0 liter mpi with dual cooling Where is the Lifting eye ?

    Agree with this unless you have the thermostat housing ring hook installed, if its there use it. Loosen the top nut on the engine mount. Pick the front of the motor up until it is just off the front mounts. Adjust the lower nut until it makes full contact. Now lower weight off of motor...
  2. alldodge

    Bravo 3x power trim wiring harness diagram

    Here ya go
  3. alldodge

    Looking for a switch

    Find a plastic outdoor electrical box, couple extension cord connectors for the box, and a 120 wall switch and cover like the one below. Make your own, this is rain tight stuff. Or search for outdoor extension cord with switch and find things like this...
  4. alldodge

    Quicksilver 3000 Controls Replacement

    Yes, the limit switch is located on the drive. So if its connected to the trim switch, pressing the trim buttons will not allow the drive to go up all the way. If the limit switch is not there, or if it is bypassed the limit buttons will fully raise or fully lower the drive. It can be...
  5. alldodge

    Mercruiser 5.0 MPI no start/spark

    Some wiring diagrams
  6. alldodge

    Using boat during winter

    Look for drain kit 22-861505
  7. alldodge

    Tilt trim motor issue

    Are you looking for these items? If not, either post a pic or let us know which page the parts are on in the manual
  8. alldodge

    Loose engine mount found !

    Muc is correct, I pay more attention to the lock nut on top. The listing only calls it a nut but it is a nylock nut http://www.mercruiserparts.com/bam/subassembly/31770/1939/250
  9. alldodge

    8.1 Crusader winterizing ??

    What most do, is take a piece of aluminum, cut the shape out, then drill and tap a hole for the air fitting, then use a piece or rubber as a seal. It could be made from ply wood, but would need some kind of metal strap to go over it to screw down in place Some use things like sea flush for...
  10. alldodge

    Mercruiser MAG 350 with Alpha drive running hot when pushed hard

    I asked if you had a belt driven sea water pump on starboard side and you said Your pic shows an arrangement which does NOT have a belt driven sea water pump The belt driven one looks like this So if you have the pump you should not have an impeller in the drive
  11. alldodge

    1998 Merc 7.4 MPI won't start

    NO The jumper cables are being used to add additional grounds only from engine block to the battery, don't use them any place else. The slave terminals are the ones on top. One side is hot 12V and the other goes to the starter solenoid. When jumped across it should crank the motor without...
  12. alldodge

    What Mercruiser outdrive do I have

    Drives, and Bravos are new style swept back shown. The B2 turns a larger single prop then the B1
  13. alldodge

    Heat Pump Issue

    Electronic, and the AUX light is top left of the display
  14. alldodge

    Heat Pump Issue

    Starting to get a house ready for rent and has not been lived in for about 3 years. Has a 2 1/2 heat pump by Rheem. When placed in heat, the electric coils turn on but the outside unit does not. The thermostat lights up AUX on the panel. If I go to cool, outside unit turns on and unit works...
  15. alldodge

    New to me bCrownline with problems high idle water in oil!!!!

    Where does the transom hose go to? You have the fuel pump section but not the water pump side?
  16. alldodge

    Help Re-Wiring Evinrude 88 SPL

    I found 87 also and think it should be 88M instead of 88W http://www.maxrules.com/models/OMC_models_files/1980_1999/75_150.html
  17. alldodge

    Can't Remove Flame Arrestor

    Pic's a plenty
  18. alldodge

    Help Re-Wiring Evinrude 88 SPL

    The motor was running fine 2 weeks ago, if it no longer runs what happened? This one looks like a trim sender This looks like a digital pigtail Main connector Where did these come from?
  19. alldodge

    Fitting a serpentine alternator on a Mercruiser SBC 350

    It might but your going to needs different brackets and probably a different ALT. Your motor year which is being used did not use a serpentine. In 1998 to 2001 used these arrangements. If you have an Alpha its top left, Bravo top right, with ALT bottom right pulley on both After 2001 the...
  20. alldodge

    Bennett Trim Repair And Auto Pro Install

    Installed the ATP unit next to the trim pump. This was the easiest place with the limited cord. The cord is about 2 feet and was glad my unit needed the adapter connecter which gave me another foot, would suggest at least 4 feet. If the motor was out, I would have placed it closer to the pump...
Top