Search results

  1. R

    Hard start

    Well it sounds like the electric primer valve is working.-----There is a wee filter in the electric primer valve.---Have a look at it.----And perhaps look at other issues to do with starting.-----Battery load test.---Starter motor inspection.-----This should be easy to figure out !
  2. R

    Hard start

    Are you pushing the key in while cranking the motor over , yes or no ?-----If you are running batteries dead I would also now look at doing an inspection of the starter.----Or test the function of the primer valve.----When motor is running and you push in the key what happens ?----Does motor...
  3. R

    2003 Mercury 25 HP won’t crank

    Mixing gas and oil at 50:1 or 4 stroke ?----Replaced water pump impeller recently or never ?---Pull starter apart for inspection.
  4. R

    1996 Mercury 25hp shortshaft lower unit replacement

    Your local shop might assist in removing the propshaft bearing carrier.( left hand thread ) if you buy some oil maybe.-----No shimming needs to be done when changing out the propshaft.
  5. R

    1984 50hp Evinrude Overheating

    Overheated?----Do a compression test first.
  6. R

    Determining Whether or not to Rebuild 1990 17' Larson

    What I think.-----Many folks are misled by the concept of a fiberglass boat.-----The fiberglass can stand the test of time but not the cheaply made ( often ) wooden structure hidden out of sight.----Water gets into the wood and it rots.------Turning many nice looking boats into worthless...
  7. R

    Determining Whether or not to Rebuild 1990 17' Larson

    You build the extra support / bunks on the trailer so that there is little chance that boat will distort while you have structure out out of the hull.
  8. R

    Determining Whether or not to Rebuild 1990 17' Larson

    I am doing a 40 year old 17' boat now.------The materials ( structural ) used in boats 40 years ago can be described as DISGUSTING.-----I am redoing this boat with composite material.----Carbon fiber / kevlar and West System epoxy.-----Not keeping track of the coins or time involved.----There...
  9. R

    9.9/15 Front-to-back Armature Plate Movement

    Lot of work involved in changing the upper bearing !
  10. R

    Chips in the gel coat on hull. Is it an issue?

    Easy fix I say.-----You pay $100/hr because the shop hopefully does flawless / can not see the repaired area.----But working for yourself is different.
  11. R

    89 40hp carb solenoid pump leaking

    edited
  12. R

    where can I find a chart for shift rod hight

    I have it saved on my computer.----Found it using that google thing.
  13. R

    Idles to fast

    Adjust the black plastic nut thingy on the throttle cable.----On the motor end of the cable where it is clamped.
  14. R

    CANADIAN SERIAL NUMBER

    A 7219595 would be a 1985 model.
  15. R

    Was given an old Searay with a Johnson 70 on it. Looking for advice

    You should be running with a 15" propeller I say.
  16. R

    Boat only runs in reverse

    A 1965 , 1979 or 2000 model ?----A six cylinder inline or 3 cylinder ?---But call the shop.----Perhaps they had a novice mechanic on the job.
  17. R

    Steering and throttle control

    Depends on your budget.----Contact a dealer like ----evinrudeparts.ca----They might know how many coins it takes.----Give them you payment ID and they might send you the parts.
  18. R

    9.9/15 Front-to-back Armature Plate Movement

    It is a strong magnet and yes you will see that on all of them.
  19. R

    Can anyone tell me what year this motor is?

    The 1966 had the battery powered points distributor.---The 4 barrel carburetor.-----The 67 model had electronic breakerless distributor.-----The 68 model did not have the belt driven distributor.----Picture of the back of the block allows for near instant ( 2 seconds ) identification.
  20. R

    Pressed in hub - remove or find washers?

    You need a hefty press to take that out.----Not sure if a flo-tork kit will fit either.----Is 21" pitch the prop you need ?
Top