Search results

  1. alldodge

    12-24 volt plug and receptacle

    Here is a 3 pin, but a 4 pin would be the same but have one pin not used
  2. alldodge

    mercruiser mx6.2 mpi

    Howdy Start by check for power at the stop switch, then go to the coil and check for power at the key switch the "I" terminal. Then pull the engine connecter and check for 12V at terminal 5. If that checks out there will be 2 relays and 3 fuses on the motor, check the fuses and swap the two...
  3. alldodge

    Help identifying volvo engine and part

    From what I can find it is the water pump, original pump is no longer made and the replacement is 23000 EUR (25534 US) but that had to be a misprint or just not made. Appears you can find all the other parts. Parts can be ordered from iboats...
  4. alldodge

    1990 Rinker 236 sport cuddy restore-Stringers and motor mounts

    It took me a bit to figure out which end was which, but think I have it so my pic is for others to maybe make it easier. My opinion of why and how is; Rinker has made a box beam to support the motor and transfer the thrust of the drive thru the hull. The reason for glassing down the first...
  5. alldodge

    motor guide trolling motor

    It's always best to let us know exactly what your working on, in this case a model number could help a bunch. This might help, but might be the speed control
  6. alldodge

    Sae J1171 Marine

    In most cases the trim pump is on the starboard side but can also be on the port, so it's probably the trim pump. It will look like this
  7. alldodge

    Rich idle

    Rough idle - I would start with checking plugs, wires, cap and rotor. If plugs do not provide any insight to running rich or lean, and there are no issues with higher rpm's, then my next thought would be fuel pressure or injector needs cleaning or replacement. Need to do some diagnostics...
  8. alldodge

    Mercruiser 5.0 TBI hesitation at WOT

    IMO suggest checking fuel pressure first, should be 30 psi at 1800 rpm using a fitting placed in line with the TBI, part number 91-806901
  9. alldodge

    Windlass anchor winch not working

    My guess would be either your solenoid has gone out or there is a bad connection. The red light on the breaker should come on when the switch is pressed. The light would not come on if it tripped. Go to the solenoid and measure across the two terminals marked POS and GND, there should be 12V...
  10. alldodge

    72 Thunderbird Formula w/twin 165hp Mercs

    Prestolite Oildyne Now Oildyne does make a replacement pump which resembles the new pump but pumps differently
  11. alldodge

    Steering issue . 1990 mercruiser 5.7

    A PS pump, will pump fluid all the time. It comes out of the high pressure side and comes back in the low side thru the cooler. Only when the steering is moved does much pressure develop. Did it ever run out of oil? If it did, they burn up fast. I would start with disconnecting the drive...
  12. alldodge

    Converting from OMC to Mercruiser

    Gauges are gauges, they will hook up and work if wired correctly Unable to say if the shift cables will work, they may have different length stroke and pivot points. Need someone with a better understanding of OMC. As for steering it will depend on the cable end and connection type, the one...
  13. alldodge

    Replacement Windshield for Islander 191

    If you do it this way it will direct upload
  14. alldodge

    Converting from OMC to Mercruiser

    From what I find the plugs are different. You can get a Merc pig tail and replace to match up. http://www.hardin-marine.com/p-13226-mercruiser-style-wiring-pigtail-mercury-plug-instrument-side-12.aspx http://www.boatfix.com/merc/servmanl/13/13e4r2.pdf
  15. alldodge

    u-joint spanner torque table

    The chart
  16. alldodge

    1989 Chaparral Transom Repair

    Most boat manufactures do it this way. Just make a rounded place with the wood and give room for layers of glass when installing. Also keep the transom from sitting flush against the bottom of the hull, I used about a 3/8 to 1/4 gap and wrapped glass around to the bottom.
  17. alldodge

    Is this rust a concern? DF140

    I would take them apart and determine if they need replaced. Could be all that is needed is clean and maybe some paint. The one spot that I did notice is the ground connections, suggest looking closer at them
  18. alldodge

    Wave height vs Seas in feet.

    In fresh water (not talking great lakes) it would be called a 1 foot chop, or waves. In the ocean it would be Sea State 2. Sea State with pics http://www.wdcs.org/submissions_bin/WDCS_Shorewatch_Seastate.pdf All states in Meters
  19. alldodge

    I/O jumping out of gear?

    I would suggest looking at the clutch assembly closer, look for rounded corners on it
  20. alldodge

    Bellows Expansion Tool

    How about this
Top