Search results

  1. alldodge

    New guy here with a boat/motor swap situation NEED advise/help/info PLEASE THANK YOU

    Guess need to ask the OMC folks to see if the OMC hole is the same size or larger then the Merc. Here is Merc I found this but do dimensions Best if posted in the OMC section since going from Merc to OMC
  2. alldodge

    Crownlne 2005 270cr Questions

    The beep is normal and tells you your computer is working, it will continue until the engine is started. If it goes off with the engine running you have a problem. If it ever goes off and is a solid sounding beep, its either lost oil pressure, drive lube is empty or engine is over heated. Two...
  3. alldodge

    transom question on zinc anodes

    We canot see what your seeing due to we have to be a member of ifish. You need to pot 2 more times to be able to upload pics. So post two more times then either use the direct link or upload
  4. alldodge

    Hot wiring a 3.0 on the garage floor

    Put a jumper between pins 5 and 6 on the engine connector. Red/Purple to Purple
  5. alldodge

    Formula 27PC Complete Power plant rebuild

    Pulled the boat out today and winterized. Here you see a strength edge with the transom and it's right where it should be from my point of view Here is the hook, first I thought it went across the hull but the only hook is just on the outer 12 inches of the hull and just in front of the tabs...
  6. alldodge

    5.7 Bravo Winterization

    You should have power steering oil cooler unless yours is an inboard. If it is an inboard and have full hydraulic steering, there will just be a tube where the power steering cooler would be. Don't bother with the Thermostat
  7. alldodge

    Help with part number

    Looks to be a CA 27319 adapter kit, or a Teleflex adapter (probably made for Merc) see list below...
  8. alldodge

    Bravo Drive Bellow installation

    Here is what it should look like
  9. alldodge

    Boat too heavy

    I'm assuming funds are limited so the reason for trying this, other wise could call a hauler. Going to try a different approach, this will stand a better chance if you can make some bunks. This still is iffy but should work if its built right. At least a 20 ft trailer, longer is better Can...
  10. alldodge

    Chrylser 105 Conqurer

    Haven't been taking many pics Added glass to everything, but did not go all the way up and over on outside stringers. Started to paint everything with epoxy paint but then just did the keel and stringers. Still thinking about adding one or two cross braces, if I do this it will be a mod...
  11. alldodge

    Quick wiring question

    This is typical boat wiring
  12. alldodge

    Mercruiser 4.3 will not turn over

    Here is the slave solenoid/relay part number 89-96054T The bottom two terminals are used to energize, the top two terminals supply power to the starter. The wiring diagram below shows the 20amp fuse (b) and relay (c). One side of the key start circuit goes to ground the other comes from the...
  13. alldodge

    Can't upload photos anymore

    Try this method
  14. alldodge

    Worlds First EV Car to Tow a Boat

    Your upload files didn't make the trip. To upload a file follow these links Kind of a long story, so if there was a question this old guy missed it
  15. alldodge

    4.3 Volvo penta won't start

    This is a Merc but the sequence is the same. The run circuit is not here, just the start. Red is full time power, once key is turned to start the Yel/red happens As tlewis mention above and I tried in your other thread, we both think you have a brand new starter problem.
  16. alldodge

    Bravo 3 Catastrophic Failure

    As always things like this bug me so did more digging and I think I figured out what happened. Basics for process, parts breakdown. Carrier has an o-ring in front of threads. Behind it is the retainer nut (item 41), bearing race then shims Here is a pic of my B3 housing prior to...
  17. alldodge

    Bravo 3 Catastrophic Failure

    Let me try it this way Maybe a formula forum thing
  18. alldodge

    '63 Gale 40hp temp gage

    Unable to say about your motor but here is a simple wiring diagram. In pic below there could also be another wire which could power the light separately. Another thing, since you have an outboard you may also need another switch to turn power on to the gauge unless it's taken from the...
  19. alldodge

    Bravo 3 Catastrophic Failure

    Guy on the Formula forum had the Bravo 3 carrier come off while running. From the looks of the drive and boat hull it appears to have been well maintained. This is a 2008 37 PC with twin 502 weighting in around 18.5 K. Owner stated So the big question is has anyone ever seen or heard of this...
  20. alldodge

    Mercuiser engine replacement

    If your new engine uses a MEFI 5 ECM with a 555 CAN bus then the 14 to pin connector will work if current gauges are wired correctly. 14 to 10 pin adapter Gauge wiring Now if your engine has a CAN buss which uses smartcraft gauges and guardian mode, the wiring harness connector above will...
View older results
Top