Search results

  1. alldodge

    Single engine for liberator 261?

    With twin 350 weight is 6180 With twin 460 weight is 6800 100 gallons gas 6.15 = 615 lb Battery 50 lb each Max load gear and people 3640 http://www.fourwinns.com/upload/Documents/Catalogs/1990/Catalog.pdf
  2. alldodge

    2000 7.4l MEP intermittent alarm

    You have a MEFI3 module and there can be a few things. My first thought would be the engine is sensing a knock but could be something else. Need to read the codes to determine what is happening. You can buy one premade, just search Mercruiser Multifunction Indicator Lamp or make one with a...
  3. alldodge

    1976 Chrysler 105 - winter project

    Just upload Pics from your computer
  4. alldodge

    Wear Ring Issue

    Did the freezer thing and removed the old wear ring. Took the new 155mm ring from the freezer and slide it in part way and it started dragging a bit. Pulled back out and measured with a micrometer and was the same thickness as the old one in non-wear areas. Put it back on and pushed it down into...
  5. alldodge

    2008 Ram 2500 6.7L AC clutch bolt

    Thanks Scott Just remembered, I bought a compressor and dryer for my 2000 Doge, but never installed because turned out it was the evaporator. Either way it won't fit, and this compressor has a stud with a nut. Pics from the 2008 model uses a bolt and nut. Looks like I have the right oil...
  6. alldodge

    2008 Ram 2500 6.7L AC clutch bolt

    Pics
  7. alldodge

    2008 Ram 2500 6.7L AC clutch bolt

    Good thing I back the truck up yesterday and left it running, I heard a slight noise under the hood, couldn't hear it inside the truck. Turned out the clutch end plate was laying on the fan shroud. Appears the bolt had broke off. So I have a small maybe 3/16 diameter stud sticking out the end...
  8. alldodge

    Draining Mercruiser 5.7

    This is the main reason when you post a question you need to provide your serial number or at the very least the year. Suggest putting it in your signature so we all know and you don't need to remember. You might be talking about cool fuel if you fuel injected The blue plugs should screw into...
  9. alldodge

    1996 Mercruiser 3.0 Alpha One turns over and over, won't fire

    Instead of checking the cannon plug yet check at the Alternator and the coil with the ignition on, if its not there check the cannon plug
  10. alldodge

    72 Thunderbird Formula w/twin 165hp Mercs

    I think the problem is with doing the hose routing of a 1978 and later system with your system which is a 1972 So if your going to hook it up using the 1978 and later setup, remove the valve IMO. That said, I also think if your going to redo the hoses without the lock valve, you need...
  11. alldodge

    replacing manifolds on 5.7

    There were 3 designs used during your model and below is the old (design 2 yours) and new (design 3). You will need to replace your thermostat housing with the new design (860256A3). Both use the same water pump, but in the pic note the circulating water pump hose is on the opposite side. You...
  12. alldodge

    3.0L to 4.3L mtr mounts and 25 yo transom

    Just noticed something, and hope like heck this is not an issue: 3.0L 25.3 inch long 7.4 inch from bottom of flywheel to center of crankshaft 8.9 inch center of crankshaft to outside edge of block 21.9 inch tall 4.3L 25.4 inch long 11.15 inch from bottom of flywheel to center of crankshaft...
  13. alldodge

    ***Knocking sound from outdrive*** NOT gimbal, helping my nephew

    I use big C-clamp and a socket, but have also used a hammer and socket. They do make the U joint tool
  14. alldodge

    Significant but strange engine problems. 5.7L Mercruiser MPI Horizon.

    Your correct, for a MEFI 3 you need a scan tool, a Merc timing 91-805747A2 or jumper these points on your DLC
  15. alldodge

    Significant but strange engine problems. 5.7L Mercruiser MPI Horizon.

    Mannual 24 is for CSB 1998 to 2000 {quote=]Would you guys happen to know what Manual I should be looking for with engine serial 0M093415? That serial number is for a 1998 350 mag mpi horizon The older model pump can still be found just search "mercruiser 861156A1". Also Airtex makes the...
  16. alldodge

    Chrylser 105 Conqurer

    Well got the foam out in
  17. alldodge

    replacing manifolds on 5.7

    You should have the one hose feeding the manifold from the bottom, if that is the case they should be plug n play. You will need the restrictor gasket with the hole. Note the hole goes at the highest point of the manifold which is usually the front
  18. alldodge

    Newbie Boater

    Howdy Bluedart I say pull, but if there is a button in the center, you might push to go to throttle only position. The red button under the handle is pulled up so you can move the throttle to forward or reverse. The leveler locks in neutral position, so it is squeezed up and then the lever...
  19. alldodge

    Thanks guys

    Was having to delete the messages in order to be notified of another post, now they go away when I look at the thread. Thanks a bunch
  20. alldodge

    Broken Drain Plug Mercruiser 7.4

    Since you have the plastic plugs this should be a bit easier. The plastic plugs get screwed into an bushing (item 4). Remove the adapter and get the plastic out then reinstall or get another. http://www.mercruiserparts.com/Show_Pictures3.asp?dnbr=809994...
Top