Search results

  1. alldodge

    bilge pump

    If your turning the switch on the dash to ON then it will continue to run. The switch should have two positions and when on it sends power to the pump, in the "Automatic" position the power is controlled by the float switch in the bilge. Note the Off position should not be there in pic below
  2. alldodge

    Ruger LCP vs. S&W Bodyguard

    Haven't tried either of those, I have the Kel Tek 380. Think they should all be good for close-in self defense. Appears the Body Guard has a safety and the Kel Tek is the smallest
  3. alldodge

    Missing drain plug....Will I have to replace engine?

    Air doesn't freeze, but once you get all the water out, knock your self out if that's what you want to do Your drain on the starboard side should be located with the knock sensor
  4. alldodge

    Tire Chains

    Have not used tire chains in many years. Previously used link and wire, link rougher riding and more noise but also were better at moving. Wire less on both sides but wound up lasting longer. Looking to get some for my truck if we ever get a bad winter it would be nice to have on hand. Have...
  5. alldodge

    Exhaust manifold swap

    Did you check on the inside? Here is one which looked fine until the hose fitting was removed
  6. alldodge

    Sea Water pump required for closed coolong system ?

    Well SJE designed the system to work with the alpha drive pump, so I agree with Ted and just use what you have. If you go with belt drive pump, I suggest go get a serpentine belt and change your pulley's. Bottom right (Bravo) routing
  7. alldodge

    Old Reddy Heater need motor

    Thanks for all the replies but maybe this will provide more clarification of what I'm dealing with
  8. alldodge

    Old Reddy Heater need motor

    Motor casing is 5 by 3 1/4 inch
  9. alldodge

    Old Reddy Heater need motor

    Have a very old Reddy Heater M100D. Been working great for all these years (about 25) until today. The motor would just hum, so I flipped the fan by hand and it started and heated up my area. Later took the motor apart and found the front bearing was dragging. The short of it, the front bearing...
  10. alldodge

    Home LED lights

    All the packaging states the LED will last 100K plus hours, only issue is the circuitry controlling the LED's don't. All these lights cost from 20 to 50 bucks each, so replacing lights is costly. Have replaced two outdoor (12VAC low voltage), one went after two years, current one is one year...
  11. alldodge

    Help with excessive fuel consumption 4.3gxi-ef

    Try this method
  12. alldodge

    Help with excessive fuel consumption 4.3gxi-ef

    Delco Go Figure, I zoomed in and can see ITR4A15. Suggest checking the gap on the plugs as well
  13. alldodge

    2003 MERCURY 150hp EFI ALARM THEN ENGINGE SHUTS DOWN. PLEASE HELP!!

    Here is a list from the manual I think your engine is in. From the list a solid horn would be overheat, over speed, blocked water passage or oil level
  14. alldodge

    replacing glass fuse terminal block, need help

    This helps but not a whole lot because we cannot see where the wires go. Your adding wire but were unable to see where it goes. Maybe make a list of where each of the wires go, and include switches or anything else that is connected to it. Other then the one wire I'm asking about where it goes...
  15. alldodge

    AT&T contact storage request/demand

    ATT installed some software (SW) about a week or so on the wife's smart phone. It want's her to allow ATT to store her contact info on their server for backup. She continues to decline the offer and the real problem is it won't let her get to her contacts on Google. Just spent an hour with tech...
  16. alldodge

    Keel sealer and mounting anode to transom

    Attaching an anode to the negative terminal will do nothing to help. As before
  17. alldodge

    Mercruiser exhaust cheater tube

    Yes, while not designed for the Alpha, if it is installed on the transom plate it should go over the bell housing side, that is if it is not deformed. Is it to long or just not going over the end?
  18. alldodge

    replacing glass fuse terminal block, need help

    My first thought when I see this is Rats Nest Looks like you have a lot of yellow wire. Looking at a bunch of wires but not knowing where they go is meaningless. Look at it this way Below is a similar setup but look at it with this in mond. Red wires are hot and Black are negative.
  19. alldodge

    Near miss, anchored pleasure boat and tanker

    They mention the anchor but in my review it was never down. Here is a pic when they came up on them and another as they first pass
  20. alldodge

    replacing glass fuse terminal block, need help

    Just to give you a pic to look at You don't have to attach stuff like I have shown, just an example. All negative returns from lights, radio and other stuff get attached at the Negative buss bar
Top