Search results

  1. alldodge

    AGM And Wetcell Battery Charging

    I would suggest disconnecting one of the start batteries from the 3-bank isolator along with corresponding ALT connection, My guess would be the house Bat is in the middle of the isolator and start Bat's are on the outside. Don't take my assumption you need to verify. The ALT sense lead comes...
  2. alldodge

    Starting battery 2 motors problem

    Should be able to do it with a 1, 2 or Both battery selector switch. Instead of two batteries and one motor just swap the connections
  3. alldodge

    Trailer Wheel Coming off

    Not being there to look closer, my opinion is get a new axle. While you could probably get the inner race of the bearings to seat sufficiently enough with some work to not cause an issue, I don't think you will be able to get the seal to seat properly. First time in the water it may leak and...
  4. alldodge

    Best way to move dirt?

    That's a scraper. If you can afford the rate it would make real short work of the project. It takes a permit to move it unless he can drive it off road to your place Keep in mind, they do flat work, so they may not do so well in a pond but it is worth asking
  5. alldodge

    How to do dual battery

    Howdy Need a battery switch and manually move it to both after motor is running OR A battery switch and an automatic charge relay ACR OR A battery switch and an isolator OR Just and ACR or isolator
  6. alldodge

    Salt Run Boats

    I haven't
  7. alldodge

    AGM And Wetcell Battery Charging

    The isolator is normally connected to the output of one ALT and then goes to the start bat and house bat. Another way of charging the AGM is changing the 2-bank isolator to a 3-bank This is how my Formula is connected and I have only on engine
  8. alldodge

    AGM And Wetcell Battery Charging

    OK, I guess. Something doesn't add up between the house the statement of charger does not charge the Gen battery. This will work, use an ACR and where the house battery is listed use it as your AGM's.
  9. alldodge

    What happened to the beeper

    Well lets retry this with more info. Accomplished some tracing and ringing out of wiring and I might be getting close to the answer. If I understand it correctly there are two different MEFI3 modules. The early modules used pin J1-4 or J1-6 and may have been connected together internally to send...
  10. alldodge

    Exhaust Manifolds and risers on 4.3L, how to tell when they need to be replaced?

    Here is a V6 but they also make them in V8
  11. alldodge

    No! Emergency ;) :) :) :)

    Have 10 1/2 inches on the ground
  12. alldodge

    Where do I clearance the gimbal ring?

    pic
  13. alldodge

    surge brake problems

    Good to hear they are going to help. Agree trying to back up disc without a block off is just no good. If you have a lock out like on this attwood coupler you can get it to back up, by moving the lever down
  14. alldodge

    1979 Switzer Super Sport Molding/RubRail

    Found a Switzer and appears to be something like what Seadoo used on their older models. Issue from the pics I cannot tell how it is held in place. Found several places which sell the rub rail and look at this one. It is two piece but may work. What keeps the top and bottom together...
  15. alldodge

    Installation of electric fuel pump 2003 90 HP Johnson OB

    Just thought of something that could expand on what Faztbullet listed in the previous link and pic below. Instead of installing a check valve where shown, just place your primer bulb inline where the hose is shown. The primer bulb has the check valve in it.
  16. alldodge

    Gas gauge sending unit/ '95 Bayliner LS1700

    I would start to verify that it is the sending unit. Get to the back of the gauge and check for 12V when the key is turn ON. If 12V is present ground the pink wire off the S terminal, the gauge should peg full. If this all works then you will need to get to the tank.
  17. alldodge

    Cant find this part anywhere?!

    If you had your serial number it would help, you could just look it up https://www.mercurymarine.com/en/us/parts-and-accessories/parts-catalog Are you talking about item 14
  18. alldodge

    1991 rinker trolling motor help!

    You could add an access cover and then add clips to reinstall the seat
  19. alldodge

    Water distribution housing leak

    Here is a pic of the front of the motor of the earlier model. A serial number is best for us to help out. Also have a question are you using the purge pump every time you pull the boat out?
  20. alldodge

    Strange starter problem

    Looks like you have a remanufactured 350 by Mercruiser . The standard 350 has a 4.000 bore x 3.48 stroke. If the block is bored .030 and increase the stroke (3.75) you get a 383. The image below I got from Merc site...
Top