Search results

  1. R

    1978 18ft Mariner Floor Rip Out: I have some questions..?

    If your funds are limited for a new boat like that ( $30,000 + ) then you have the opportunity to make this project so that the grand kids will enjoy it.-----New boats may have the same shoddy materials hidden by fancy carpeting.--------Look into composite materials for this project.
  2. R

    1978 18ft Mariner Floor Rip Out: I have some questions..?

    Time to get the " beaver puke " out of this boat.-------There are composite ( not cheap ) materials that will last longer.-----This looks like it was refurbished once already.
  3. R

    1981 Johnson 70hp: How to remove remote control cable from motor:

    Use a 7/8" wrench to remove that bolt.----Or remove cotter pin and pin on linkage .----Your choice and both easy.
  4. R

    1969 6HP Impeller replacement

    The thermostat normally fails in the open position.------Missing because folks simply do not know how important that part is.-----And a very common thermostat that was used for many years from about 1960 to 1998 in some motors.
  5. R

    1989 evinrude 140hp low compression

    Perhaps your local machine shop can machine away the corroded material for say 1/2 " ( 12 mm ) and then shrink on an aluminum ring.----I would do that if I was stuck for a block to use.----Have a bunch here but you are too far away , across oceans.
  6. R

    Has spark and clean fuel, wont start

    Very hard for the timing to go out of adjustment on these simple motors.
  7. R

    Has spark and clean fuel, wont start

    The timing simply does not go out of adjustment.----Well ,----- except for a sheared flywheel key !
  8. R

    1982 evinrude 15hp has fuel spark and compression no crank

    Check the flywheel key.
  9. R

    Outboard motor test tachometer

    Searaider----Do yourself a favor.----Google-----smartphone tachometer------See what technology can do for you.
  10. R

    Outboard motor test tachometer

    Some smart phones can be adapted to perform a tachometer function.----Just stick some reflective tape on the flywheel I think.
  11. R

    1984 johnson 90hp carb leaking fuel out air cleaner

    ??----Them 4 valves are called ---check valves ----in the parts book.-----I always thought a check valve flowed one way only.
  12. R

    Need help to identify this Evinrude.

    Another KIJIJI special in Ontario.----If Electric shift it be a 1971 ( most likely ) or 72 model.---Post pictures of lower unit.-----Or post pictures of shift linkages on side of block.----Or control box. -----Is there a big yellow plug on the wiring harness ?
  13. R

    1979 OMC Gear Lube

    Boats like that must be , and are often scrapped.----Or they must be repaired properly.-----If a hull like that fails in Canada ( ice cold water ) with the boat sinking the event might be in the newspaper.-----It sadly won't be on the sports pages.-----
  14. R

    Mercury 200 20hp need to find out which year it was built

    The decals clearly indicate a 1978 model.-----There were issues with upper and lower ball bearings.----Not quite hefty enough.
  15. R

    Long shaft vs short shaft

    Hopefully they use stainless bolts on those big multi engine center consoles.-----See them on those ---haulover inlet videos.-----You would not want those $35,000 motors to fall off.-----Not all STAINLESS is the same.
  16. R

    1987 mercury 60 hp piston damage

    Heat ( boiling water ) will expand the hole in the piston.----Putting pin in the fridge will shrink it a wee bit.------Might slide together.
  17. R

    1969 6HP Impeller replacement

    No need to remove powerhead to change impeller.-----But there are some steps that need to be followed to get the powerhead seal pin to come through a slot.------The 69 model has needle bearings on big end of the rods.-----Thermostats are often missing or stuck open.
  18. R

    1979 OMC Gear Lube

    Well-----That mess is no surprise at all.----Looks like some repairs had been done already on it.-----Support the hull in a frame.----Cut that junk out and put some composite material in there.-----Most folks would say that there are better / easier projects around.-----Your location.
  19. R

    1979 OMC Gear Lube

    Well----60E ---appears to be from the Bracebridge / Muskoka area.------I see ( in the pictures ) some issues with stringers / wood under the floor in your future.
  20. R

    Trying to start a 1967 33hp Evinrude no Generator

    Or bring it over for a tutorial on how to look after this fine motor.----No manual needed here for that simple machine.
Top