Search results

  1. Scott Danforth

    The Equipment Wish List - Recommendations??

    FWIW, a 7" Garmin with down view / side scan can be had in the $600 range I know its readable at well over 50mph, and the side scan is good to about 20mph if you wait a month, the unit you were looking at will be reduced again as new units come out.
  2. Scott Danforth

    The Equipment Wish List - Recommendations??

    BTW, if you want better than 2 meter accuracy, you have to be military
  3. Scott Danforth

    Lifting the Engine 5.7L - Weight

    with exhaust and heat exchanger and fluids, expect about 800# stock lift points are best, loop on front of thermostat housing, one loop on back of each cylinder head. however without the front loop, find one of the other bolts in the front of the head. or pull the exhaust manifolds off and...
  4. Scott Danforth

    2006 Merc 8.1

    have you looked at manual 33?
  5. Scott Danforth

    Adding Transom walkthrough to wake boat

    please explain this shop that would only charge "couple hundred dollars" i have a whole bunch of fiberglass work to send their way then. Just the upholstry work alone will be over a grand, the fiberglass work will probably be in the 2-3 grand range.
  6. Scott Danforth

    1996 Volvo Penta 7.4 will not stay running

    go back to basics what is your compression? what is your fuel pressure? running for a minute and stopping is lack of fuel. i would look at the fuel pressure to confirm. Volvo's get their non-cranking fuel pump voltage from the alternator.
  7. Scott Danforth

    The Equipment Wish List - Recommendations??

    what is your budget, also remember, there are a bunch of sales that are coming in a week
  8. Scott Danforth

    1996 Volvo Penta 7.4 will not stay running

    carb?, injected?
  9. Scott Danforth

    No spark plug spark... 170 MC , 1985 Sea Ray

    you have a bad wire to the I/R terminal on your starter. start with the factory service manual and follow the wiring schematics.
  10. Scott Danforth

    2003 SeaRay 200 Bowrider seized engine????!!!!

    Need to know what is wrong with the OP's motor first. could be something minor, could be major. hasnt been back since he started this thread.
  11. Scott Danforth

    Specific paint for outboard motor?

    factory mercury paint is PPG / Ditzler 9000 black
  12. Scott Danforth

    Specific paint for outboard motor?

    you will get better results if you use straight rustoleum, mix in some hardener and spray with a real spray gun that way you get a hardened finish with out the rattle can zebra stripes
  13. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    are they balancing the motor?
  14. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    stock blocks with roller cams do not have the machined fuel pump boss. you want a roller cam. they could fly-cut the mounting surface and drill the hole for the push-rod and oil return
  15. Scott Danforth

    No spark plug spark... 170 MC , 1985 Sea Ray

    no, the boat uses a 1.5 ohm coil requiring a balast resistor for running and gets full 12 volts when cranking via the I/R terminal on the starter. that is the way the boat is wired.
  16. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    so..... what heads will you be running? that is where you start with the determination of piston. the next question is new or used block to determine bore and deck height
  17. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    keep the compression ratio about 9.4 and dont worry about the fuel.
  18. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    you need the quench pad. make sure the final quench distance is in the .040 range are they using a used block, or a new block? the GMPP blocks have the mechanical fuel pump boss machined. the stock GM blocks do not.
  19. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    and this is
  20. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    that isnt a D-shapped piston. this is
Top