Search results

  1. Scott Danforth

    470 Distributor Mechanical Advance

    see how much slop is in the $5 distributor shaft bushing from napa also, if you didnt set your dwell with a meter, go back to that, then set timing
  2. Scott Danforth

    Boat not as fast as expected?

    Pitot tube
  3. Scott Danforth

    Boat not as fast as expected?

    being over-powered means that if there is an issue (accident, etc), you may be 100% at fault. not to mention, your transom is designed for a 150hp. so the forces of the extra 50hp may simply rip it from the boat.
  4. Scott Danforth

    PCV Question

    depends on year. used to be a hose from both sides, then they went with a PVC breather in one side and the hose on the other side. however never simply block it off
  5. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    you take the drive off you then unclamp the PDS (6 bolts), and take 3 of the bolts to jack the clamp ring off you then disconnect everything inside the boat, undo the front mount lag bolts and lift up and pull forward. your boat can not be in the water to do so
  6. Scott Danforth

    Boat not as fast as expected?

    you want to go faster, you need more power. as indicated above, with your 1983 motor that is your crank rating. your boat should be rated at 150hp. how fast do you want to go?
  7. Scott Danforth

    Deck plate question?

    if your sending unit is leaking fumes, you have a bomb.
  8. Scott Danforth

    Limited Power on Mercruiser 3.0LX Alpha

    how old is your fuel?
  9. Scott Danforth

    how to remove prop shaft seal on a duoprop DPS-A ?

    looking at the casting, the bore is a thru-bore and the retention "lip" is the 4 staked areas. that is a cheesy design vs machining a tru lip. however it would save a secondary machining step.
  10. Scott Danforth

    Pontoon in the snow

    we had to bust your chops.....
  11. Scott Danforth

    how to remove prop shaft seal on a duoprop DPS-A ?

    Did tge neighbord DPS 2 years ago, about 3 times on a stringer400, once on a stringer 800, a few times on a DPA, twice on a Bravo, once on my alpha, twice on my 290DP, a few MC-1s, about 35 or so outboards however been swapping seals on gear boxes for decades. Designed a few gear boxes as well...
  12. Scott Danforth

    Winterizing Force Outboard After Being Shrink Wrapped

    never ever heard of anyone putting AF in an outboard, much less a 2-stroke outboard to winterize a 2-stroke, change lower gear oil, fire it up on muffs and fog it until its dead.
  13. Scott Danforth

    Limited Power on Mercruiser 3.0LX Alpha

    first, what year do you have? second, not sure of any 3.0 liter with a 10 degree BTDC timing. the older points were 4-6 degrees BTDC EST was -1
  14. Scott Danforth

    OMC 2.5L paired with OMC Sterndrive 800 Outdrive

    the only way to increase value of a boat is to use it...... the value is in the memories. to simply try to trade for value, you will most likely get burned.
  15. Scott Danforth

    Pumping out 5 yr old gas and it's clear

    I would run it in your lawn mower or have a bonfire.
  16. Scott Danforth

    351 ford seaswirl cordova

    nah...... its coming across good deals and jumping on them. I have $625 in essentially a complete drive including transom shield.....bought in pieces by keeping an eye out. I am set "WHEN" something breaks
  17. Scott Danforth

    OMC 2.5L paired with OMC Sterndrive 800 Outdrive

    ask yourself the question. do you want to use the boat, or do you want to work on the boat? of all those, the 3 small aluminum fishing boats are ready to run. the fiberglass boats will be a project
  18. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    the HX's for Volvo were obtained thru Champ Products in Sarasota Florida, and sold to Volvo USA for the V6 and V8 GM motors. the volvos using the swede build motors were MOTA heat exchangers
  19. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    this is the amount of rust I get every outing plugging up a filter screen I added between my thermostat and heat exchanger. this is only from the cylinder heads which did come off a salt-water cooled motor. to this day, I still kick myself for not spending the extra $5-600 and buying new...
  20. Scott Danforth

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    you need new exhaust because your were cracked (post #1) the VP exhaust already flows better than the mercruiser versions. so all you need are BARR or VP replacments you are over-thinking 906 vs 062 vortec heads the closed cooling should only be added to freshwater motors or new motors...
Top